Search results

  1. Scott06

    Swap drives from one boat to another. How many day project?

    So are you swapping this engine into original boat ?
  2. Scott06

    Alpha I Gen II Impeller Replacement

    yes likely happened prior to this change out. In salt the rubber I believe doesn't last quite as long but in fresh I changed my neighbors original to the boat 11-12 yr old impeller, looked new. Did mine after 6 years also looked new. OEM bellows lasted 18 years. Sounds like you are on right...
  3. Scott06

    Alpha I Gen II Impeller Replacement

    That melting is due to lack of water flow from impeller at some point. There is some water flow into exhaust at all times to cool it. This is indicative of problems with water flow or impeller lost a vane I have never put anything on the screws although using perfect seal/ permatex #3 can help...
  4. Scott06

    Replacing an Alpha1 Gen1 205 V6 for 87 Cobalt 17BR

    When you say there is a gash in there do you mean tear in the bellows? If so need to replace them, they are clean enough. last pic yes that is where the annode goes
  5. Scott06

    6.2 MPI Whine noise when revs

    One thing to try have you done the same revving but at different drive angles via both trim and steering. Willing to bet it changes pitch which would be an indication of gimbal and or u joint issues despite the previous work
  6. Scott06

    New to Volvo family

    Volvo outdrives for us market are made in TN and the engine is a chevy so not as imported as you think.
  7. Scott06

    New to Volvo family

    No elegant but zip tie will be fine for years to come , it just sits there. I had a rubber band on my Datsun Z years ago, metal spring clip broke off.
  8. Scott06

    85 373v ranger with 150 xr 2 black max

    Depends on where your current WOT rpm is compared to max WOT range for engine. As stated above 19" pitch if similar style prop would probably increase WOT rpm about 800 rpm. that may put you over. Generally when propping such that you can hit the upper end of rpm range or a tad over will give...
  9. Scott06

    Help with prop ID (pics)

    Normally the Hand stamping like that are done when it goes to the prop shop for rework or repitching . Probably only way to tell is to put it in a pitch block, maybe side by side comparisons vs other black max type props sitting on the shelf. With a pressed in hub you can tell that prop has some...
  10. Scott06

    Need to determine best prop for weird setup

    In theory, as danforth points out with the timing shunt in to lock it in base mode should be at 1 deg BTDC, with shunt out it will be around 10 at idle, at 2800 or so should go up to 25 or 28 total. you just want to confirm it is advancing. if it doesn’t advance could be bad module or base...
  11. Scott06

    Replacing an Alpha1 Gen1 205 V6 for 87 Cobalt 17BR

    Use a little grease to hold the roller and shift cable end together. put it in fwd hold prop counter clockwise with bungee cord to keep it from popping out of gear you can turn it ccw to line up splines so it wont pop out of gear. Check your alignment. Should slide on with out too much work if...
  12. Scott06

    Bravo 3 loss of lube oil - slowly then rapidly x2

    The bearings are bigger than the ID of the seal so on the yoke the seal goes on first then the two bearings tightened down until you get the correct rolling torque. I bought a beam type 0-75 in lb wrench for about $65 (McMaster Carr) when I changed rear end gears in my 65 Pontiac. When I did the...
  13. Scott06

    2011 Tahoe Mer 4.3 - engine miss firing

    to add tot the list above of possible issues bad pressure regulator, stuck anti siphon valve
  14. Scott06

    4.3 LX water in the oil...

    Gen plus is the newer true Vortec head engines with 8 bolt intakes. Bolts are vertical two in each corner of intake
  15. Scott06

    2011 Tahoe Mer 4.3 - engine miss firing

    @alldodge may have some ideas but would suspect that measuring fuel pressure is probably a decent next step
  16. Scott06

    2011 Tahoe Mer 4.3 - engine miss firing

    I would start with what do the plugs look like and what does contents of fuel filter have in it? Is this carbed or injected? When it miss fires check the spark with spark gap tester, if carbed look down carb and pump throttle to see if there is any gas in carb coming out of accelerator pump
  17. Scott06

    Alpha one gen 2

    these guys sell remans I believe. https://www.sterndrives.com/mercruisersterndrives.html Confirm the ratio of the drive before ordering yours is most likely a 1.62:1. Thes guys sell the aftermarket SEI drives that many folks use (about $2100) and OEM new drives ($3600)...
  18. Scott06

    Need to determine best prop for weird setup

    Yes the Innova timing light will do both tach and timing functions. This goes over checking total advance total timing is at 6:53
  19. Scott06

    6.2 MPI Whine noise when revs

    Had the same thing on my old boat a few years back- ran fine when winterized, made a similar noise when back in in the spring. Gimbal bearing was bad, had some water in bellows , bearing gets corroded while it sits. U joint could do the same thing. Did you have a lot of water in the bilge at...
  20. Scott06

    Need to determine best prop for weird setup

    You will need an advance timing light. I have an old Craftsman with a dial on it, you can put in the advance on the dial and it should time with the TDC mark on the balancer. Just looking for total degrees of advance, with out advance engine will not make power Some more modern timing lights...
Top