Search results

  1. Scott06

    MerCruiser 3.0 Runs Poorly As It Warms Up

    Yes hook it to fuel pump inlet. So this one land then take it out. If problem goes away then you have narrowed down to tank to pump
  2. Scott06

    Need help asap please. Water out of "weep" holes after impeller change

    I think that is a drain hole for the exhaust cavity or water ports and if raised you will get water coming out. Does it stay at temp? Exhaust manis not too hot ?
  3. Scott06

    Mercontrol cables

    You would need to ohm test the switches and then jumper your trim limit Switch since you don’t have one. Entirely possible that the wiring has corrosion inside the wires. Had this on my brothers boat a couple years back, center console , harnes in water filled conduit under floor up to helm had...
  4. Scott06

    Mercontrol cables

    I thought the middle and upper needed to be pushed to get to trailer , one I think was just trim. Going off memory from neighbors old start craft
  5. Scott06

    6.2 MPI Whine noise when revs

    Never heard that noise from any outdrive before. Bravos may be different but I dont think so. surprised a mechanic would not take a look.
  6. Scott06

    Rinker 282 trailer

    Should be big enough that the rear bunks extend just beyond the transom. Either it is not actually for a 28 ft boat or the bow stop needs to come forward. you will pick up a few feet as the bow stop where it hits the angle of the bow is behind the front of the boat.
  7. Scott06

    Anybody know about Ford DIS ignitions?

    I think that is invaluable experience for a kid his age. I started screwing around with cars helping my dad, which led to me restoring old cars, learning to weld & rebuild engines/trans. When I started working in the beverage production industry in late 90's this experience helped me...
  8. Scott06

    1997 GP760 Wave Runner scored pistons and cylinders

    Agreed running lean and detonating will hammer the rings and pistons to death and ruing the motor Would be looking for fuel system contamination, proper fuel pressure, and dirty carbs
  9. Scott06

    MerCruiser 3.0 Runs Poorly As It Warms Up

    Have you pulled the siphon tube from the gas tank to see if there is a screen in it? was thinking either this , the antiphon valve may be restricting fuel flow. Cant recall if you checked spark strength after it messes up or tried running it on a sperate 5 gal tank . In the end might need a...
  10. Scott06

    6.2 MPI Whine noise when revs

    Yeah we have been through what work was done and how this can happen over the winter. I suspect you will find either water got in bellows or water got in the gear lube and corroded a bearing in the drive.
  11. Scott06

    Replacement Prop Selection

    Agreed something is not right. Would also verify firing order is correct. I thought on the SBC there are two cylinders that can get swapped wires and still run ok ish. Has tach been verified for accuracy ?
  12. Scott06

    Please help with engine type selection!

    My 65 Pontiac had a factory windage tray also not a real high Revving engine 5200 was about it before the rods left the building …
  13. Scott06

    Please help with engine type selection!

    Yeah no way a 5.0 would do that. Answer depends on what u want out of the boat and how much you want to spend. as mentioned you would be better off getting a 96 and up vortec engine . If it were me I would get a new long block and exhaust and intake manifolds . Drop in would be the same vintage...
  14. Scott06

    '88 5.7 inboard dies after running smooth, restarts after few minutes, smooth again

    Yeah Sierra is a better respected aftermarket supplier, but you never hear I bought the OEM part and it failed or was SOL in the box.. Also there are so many counterfeit parts suppliers online now. There is a toyota mechanic on you tube called Car Care Nut, he did a whole video on how to spot...
  15. Scott06

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    Hope the check out ok. Its rare that folks actually represent them in actual condition!
  16. Scott06

    Please help with engine type selection!

    What size boat is it , I think you’d be better off not loosing displacement and power
  17. Scott06

    4.3 how to remove thermostat/sleeve from housing

    Had to typically pry them out with screw driver, so do t come out without breaking them. If you go through the work to get in there dont just test it just replace no sense screwing around
  18. Scott06

    Which engine oil can I add?

    Not a problem to mix them in a non catalyst engine, as stated the blend is a blend of synthetic and conventional oil , so mixing blend and full synthetic will be a blend when combined . Use them all interchangeably
  19. Scott06

    Alpha I Gen II Impeller Replacement

    Yes upper gear case seal you should definitely inspect or do a pressure test when you reassemble. Can get damaged reassembling so be careful. o change that upper seal gear and vertical drive shaft come out, seal is like first thing that goes back in .
  20. Scott06

    Alpha I Gen II Impeller Replacement

    if you get the quicksilver merc impeller kit with the base plate and gaskets + orrings its in there its #25 in this dwg- the kit comes with a tool to install it- its just a cup you use as a gauge to slide the slinger seal down the driveshaft while lifting up on drive shaft. I think it just...
Top