Search results

  1. K

    Mercruiser 160 carburetor

    The “T” that is on the 160 was something the previous owner added. Just remember all marine fuel pumps with the small male fitting for the Tygon hose must be routed to the carburetor’s air horn so that the fuel stays out of the bilge and into the carburetor only. The style that Chris posted can...
  2. K

    need help figuring out how to remove a starter from a 1996 4.3GL

    One reason you may be having a problem is the bolts are probably metric rather than fractional. The heads may be either 14 or 15 MM.
  3. K

    Mercruiser 160 carburetor

    The Tygon hose should only connect the rear of the air horn to the fuel pump vent. Use the 165 valve cover with the vent tube connected to the flame arrestor as you posted. Engines with the plastic bowl connected to the fuel pump as in the picture Chris posted had the short hose that went...
  4. K

    Volvo Penta 4 Cyl in a 1988 Baretta

    Before you install the rebuilt carburetor add a marine approved fuel filter/water separator kit. Sierra# 18-7983-2
  5. K

    New, steering cylinder locks to starboard

    If you disconnect the cable from the control valve by removing the pin through the cable end and the cable slightly pulled out from the control valve try starting the engine, the unit should not move in either direction since the control valve has no signal from the helm. If it does the same...
  6. K

    U joint shaft

    Most times when the gimbal bearing and universal joints need replacing is from water incursion in the bellows. If so then the seal surface on the input yoke is rusted and will not hold pressure and leak into the bellows. You will then have to remove the driveshaft bearing retainer. Is the...
  7. K

    88 sea ray with 3.0 mercruiser.

    Depending on what part of the country may also help. I generally adjust the choke where the butterfly is just barely closed. Since the choke is electric it is normal for it to close on a warm engine when the engine is not running. And of course there has to be 12 volts when the engine is running.
  8. K

    Changing oil without a dipstick

    In addition to the above post universal dipstick tube kits are available a Summit. There is one that has a npt thread that will screw into the brass block that the Sierra kit has.
  9. K

    Changing oil without a dipstick

    If you cannot get a location for the dipstick this is something I have done. Sierra # 18-7891. This is the kit with a double inlet 1/4” npt and a 1/2” 20 male that threads in the pan drain. Make sure that the threads are not metric. The flexible hose is used to drain the oil through the bilge...
  10. K

    1986 Bayliner Capri won't start after running great all weekend

    there was a lot of Bayliners sold here and the dealer did not do any warranty work so quite a few ended up at my shop. I started getting complaints about hard to start sometimes. They would crank and crank and the engine would start when the key was released from start position. The added wire...
  11. K

    1986 Bayliner Capri won't start after running great all weekend

    There is something that will help the engine start quicker. Look at the starter solenoid and on the out board side there is a un used male spade connected. Make up a wire from the spade to the + or Bat side of the coil. This provides 12 volts to the coil when cranking. The genuine Volvo...
  12. K

    1977 OMC 235/Ford 351W Low Manifold Vacuum, Stalls when letting off throttle

    Go back over the valve adjustment. I only tighten the lock nut 3/4 of a turn after there is no slack and the push rod still spins. I doubt if there is any damage. There is a procedure to set the valves cold by starting @ tdc and rotating the crankshaft by hand and adjusting certain valves...
  13. K

    Mercruiser 160 mystery electronic ignition

    The one advantage the Petronics or any other conversion has is it is more tolerable to slightly worn distributor bushings. The main thing to do now is to have a machine shop add a lower bushing, replace the upper and make sure the centrifugal advance is in good condition. That way the points...
  14. K

    Finding these on I/O`s but may apply to all installed tanks

    Hey Doc, Why not give that filter a name using the most derogatory description allowed on this site?
  15. K

    1977 OMC 235/Ford 351W Low Manifold Vacuum, Stalls when letting off throttle

    That is good. When every thing is right the idle mixture screws should be 1.5 turns out and the idle stop 1-1.5 turns. Are you sure the there are no vacuum leaks from under the carburetor? Are you sure the timing marks on the balancer’s “0” mark line up with the pointer with #1 If the cam is...
  16. K

    Mercruiser 160 mystery electronic ignition

    It looks like a Mallory Unilite. The conversion may be around 30 + years old. It appears the owner took really took good care of the engine. If it is a Mallory you may not be able to get replacement components. You can always update to the newer Mallory version or a Prestolite.
  17. K

    1977 OMC 235/Ford 351W Low Manifold Vacuum, Stalls when letting off throttle

    It could just a carburetor problem. Has it been rebuilt lately? Some time just the metering block gaskets are the problem from shrinking.
  18. K

    low compression 3.0 cobra (new)

    It almost appears that you may have an exhaust blockage. Sometimes the exhaust shutters break loose and restrict the exhaust.
  19. K

    Mercarb 2BBL accelerator pump check ball

    On the Rochester model the aluminum ball is held down in the pump well with a circular wire ring. Was there a similar one in the pump well of the Marcarb? If not then that ball may have been used on an earlier model. Does the pump plunger on your carburetor have 2 plunger cups back to back...
  20. K

    Does anyone know what this part is?

    It looks like part of the kit to pull a new fuel line and filter into a weed eater fuel tank.
Top