Search results

  1. D

    The overall rundown on Velvet Drives?

    this i've found velvet drive to be the best overall straight inboard transmission. be sure to check/change the fluid regularly it will aid in shifting and noise reduction. dexron 3 atf is recommended fyi when you say "V - drive" it makes me think of a completely different transmission/drive system
  2. D

    Delco EST High Idle

    fyi MSD does make a marine ignition system that utilizes the same theory of operation as the thunderbolt ignition system. it is offered as a direct replacement for the thunderbolt system however ime it does not have the same durability as the thunderbolt as AD stated previously the delco system...
  3. D

    2013 monterey 204 fsx prop not operating

    this would be the easiest and cheapest scenario, the rubber hub in the prop could very well have spun thus not allowing the propshaft to properly rotate the prop. a lot of mercury brand propellers now use a plastic removable hub as a sacrificial and easily replaceable part. other causes of prop...
  4. D

    5.7 Gxi-f outdrive issue

    on all volvo SX-M (including most if not all other volvo) sterndrive units the shifting takes place in the upper half of the drive. the drive unit itself is comprised of two halves, the upper and lower. nowhere in your posts have you mentioned that you have removed the lower half of the drive...
  5. D

    Alpha One Gen 1- Reassembly bellows questions...

    probably but i can't say for sure, never tried it that way
  6. D

    5.7 Mercruiser(thunderbolt iv)/Alfa 1 out drive intermittent issue

    unless the lower shift cable is worn, binding or misadjusted a faulty lower shift cable can and probably will shift properly with no load, i.e. boat on trailer running on muffs. put the boat in the water with a load, cable binds, etc, and engages shift interrupt prematurely/improperly
  7. D

    Alpha One Gen 1- Reassembly bellows questions...

    attach the exhaust bellows to the gimbal housing first u joint bellows, water passage hose, shift cable assy and bellows should then be attached to the bellhousing insert the shift cable through the gimbal housing (with the bellows already slid on the cable) and ensure it is routed properly...
  8. D

    2003 mercruiser 4.3 issues

    grey wire is for the tach issue sounds typical of a failing/failed ignition sensor in the distributor, there is a good troubleshooting guide for the thunderbolt system which can easily detect most failed component(s)
  9. D

    Mercruiser 3.0 blowed a spark plug

    that troubleshooting guide is for a thunderbolt ignition. as far as i know mercury never used the thunderbolt on a 3.0 L. your ignition system is most likely the delco EST system, completely different from the thunderbolt
  10. D

    Engine Mounts Install

    when i need access requiring raising the motor slightly i've used a bottle jack under the exhaust manifold....if there is enough room between the manifold and stringer that is
  11. D

    Replacing alpha one retainer nut

    the only way to remove/install the retainer ring is to remove the driveshaft/bearing assy and dismantle it
  12. D

    Fluid in the bilge

    this the cooler is on the low pressure side of the p/s system. the lines are held in place by hose clamps at the barb fittings on the cooler. it's not a rare occurrence for the lines to become brittle and split at the ends. repair in this situation requires removal of the leaking hose(s)...
  13. D

    3.0, engine oil, breather tube questions

    everything looks/sounds normal the "smoke" you're seeing is most likely condensation being purged from the engine oiling system/crankcase. very common on 3.0 L engines. unless you are having severe power loss/other major symptoms there is no need to worry, it's just the nature of an engine...
  14. D

    1992 Mercruiser 3.0 problems running under load

    water separator would be located in line between the fuel tank and fuel pump (if equipped, most 3.0 L merc engines did not come with an oem separator). the fuel pump filter is in the pump itself, need to remove the bowl to replace it. i was referring to fuel system vacuum, not engine vacuum...
  15. D

    1992 Mercruiser 3.0 problems running under load

    there are at least two fuel filters, possibly one more. one filter in the fuel pump (mechanical), one in the carburetor and possibly a fuel/water separator. have you checked fuel pressure AND vacuum throughout the rpm range?
  16. D

    Hole in y-manifold casting

    could be the cause of the hole check the exhaust passage on the drive for other flapper parts/pieces. i've found them wedged in the carrier assy from time to time
  17. D

    Changed Bellows still have water

    not really, unless you completely clean out the bellows, reinstall the drive using a new install kit/gasket and take it out on the water, then remove the drive and see if water is present if the u-joint bellows is sealed properly the only way for water to enter is through the weep hole in the...
  18. D

    Fluid in the bilge

    pump looks fairly clean, at least no leaks noticeable in the pics. does not rule out a leak in one of the lines though seeing as how your p/s pump is nearly empty check the cooler, the low pressure lines attached to it are a common cause for p/s leaks
  19. D

    Mercruiser 3.0 blowed a spark plug

    the engine is flooding to clear the flood, set the throttle to wide open and crank the engine over. do not pump the throttle, just set it to wide open. when the engine fires pull the throttle back to a reasonable rpm if the engine wants to die out when throttling back there is most likely a...
  20. D

    Leaking Gear Lube Hose on 1999 Mercruiser Sterndrive

    as far as i know the brass one is nla, at least from mercury. you definitely want to cut the line in half before you attempt to remove the line from the through transom fitting. carefully slice the line where it attaches to the plastic barbed fitting ensuring you do not damage the barb. the...
Top