Search results

  1. C

    Old evinrude junior ID

    1986 Evinrude EJR-CDR 1.2hp Outboard Motor easy search on google....
  2. C

    1966 Jonhson 9.5 rust around exhaust cover

    what is strange is the the head bolts ended up reddish color also yet the one on the right side stained beige/silver
  3. C

    BRP Engine Tuner ?

    plugs are cheap... but a good cleaning / gapping may suffice
  4. C

    1966 Jonhson 9.5 rust around exhaust cover

    60 is on the low side but has indicated in Leroy's article these are not very high compression engines. it may come back up after a good run . try some engine cleaner in the fuel . some like SEAFOAM some don't . my honda snowblower loved it .. it cured the coughing
  5. C

    BRP Engine Tuner ?

    just use as indicated. don't make this to complicated or worrisome use the 55 gal drum if worried about pollution.... imho no need for extra cooling water your may need to be freshen up with a good cleaning of all orifies and passages especially anything to do with the low speed circuit...
  6. C

    1966 Jonhson 9.5 rust around exhaust cover

    it may have overheated long time ago ?? how is it ? does it turn or stuck solid check gear case for condition suggest you remove the cyl head and look inside while it is out you can always brush it up and recoat with high temp. paint for cosmetic reasons.. careful not to break...
  7. C

    1957 18 hp Johnson FD-11 Pinion gear part number help

    try here at IBOATS for parts ... they support this site and may very well have all you need .if not try the oldies site at AOMCI "ask a member" free classidied adds/wants
  8. C

    1988 48 special carbs

    any clue as to what in the new kit actually fiixed it all up.... was it sucking air in via the poorly packed LS needle do you think ? . the rest is float , carb gasket orifices , donut washer etc...
  9. C

    My old Motor

    to add... my 75hp ETEC 2005 has been flawless or near flawless for 17 going on 18 years. Before they R.I.P'd Evinrude my only issue was false NO OIL code 38 fixed by BRP in year 7 of ownership thanks to the proof logged in the EMM fault log memory..... since new . AT 73 it is my last one...
  10. C

    1992 40 Johnson carbs leaking

    heavy as in fuel logged (Soaked) versus ... waterlogged... the carb float normally rises with fuel and shuts off the inflow of fresh fuel in the carb ..... but just like your toilet bowl.... if your float ...does not float up water keeps leaking in the toilet bowl.... same for carbs...
  11. C

    Does this indicate water in lower unit oil?

    if fixing a leaky GC is not your piece of cake and shop repairs are to much $$$$... oil is cheap and some just replace it mid season.
  12. C

    Bad temp sensor?

    check the sensor wire for chaffing/grounding.
  13. C

    Seeking year of motor without model number

    post pictures cowl and all
  14. C

    1982 Johnson 7.5hp Backfires but No Start (Wrong Carb?)

    he switched them ...
  15. C

    1982 Johnson 7.5hp Backfires but No Start (Wrong Carb?)

    now that the plug wires are in the proper place ....just clean the carb... check the fuel pump filter if any before it dies try pumping fuel up the carb with the hose pump if it stays running thefuel pump is in need of a close look. see an old carb... much like yours except for...
  16. C

    1982 Johnson 7.5hp Backfires but No Start (Wrong Carb?)

    tried inverting (reverse) the plug wires ????
  17. C

    1996 50 hp adjustment question

    not to many option a ground usually
  18. C

    Fuel primer inop

    https://maxrules.com/graphics/omc/wiring/1988_89_200_225.jpg looking at the 89 version of the 200 hp wiring we can see that the key energizes the primer pump...electrically of course and seems no electrical CHOKING is involved in the key switch. In conclusion the only way to get some...
  19. C

    1988 48 special carbs

  20. C

    1988 48 special carbs

    why not tell us if you popped the dime size plug on top to clean the low speed circuit of the carb. did you confirm carb cleaner flow via all orifices did you line up the proper carb gasket mounting holes... all of them incl. the side channel to the top half of the carb ??
Top