Search results

  1. C

    1967 Evinrude Speed Twin 9.5

    apparently the 9.9 or 15hps are quite different beasts . your 9.5 is the choice for backwoods lakes , float plate trips etc... if it runs nice you may get a good price to invest in a bigger motor.
  2. C

    1967 Evinrude Speed Twin 9.5

    IMHO... Best to leave it humming along VS causing problems downsream
  3. C

    1967 Evinrude Speed Twin 9.5

    these flat top trollers run with low compression and are not road runners . have you done the basics .. have you pulled the FW to check for cracked coils (common issue) http://www.leeroysramblings.com/OB%20images/QD_burned_coil.jpg http://www.leeroysramblings.com/OMC_9.5.htm
  4. C

    1986 evinrude 70 hp p trim issue

    great news... thanks for your feeedback on the cause
  5. C

    1986 evinrude 70 hp p trim issue

    so trim motor sounds ok by itself 2 new relays should be good 12volt comes out OK when no load is applied (the trim motor) buzzing relays can mean not enough volts/amps to energize the relay coils properly and the fact the outpout volts drop significantly seems to indicate...
  6. C

    79 Rude 100hp - no fire

    Bubba.... bets not to wake up old issues from 2010 start a fresh post with current issues you are having
  7. C

    1990-1995 era 3 cylinder charging capability?

    if your boat sits ouside much you may want consider a solar panel to trickle charge the trolling battery
  8. C

    1994 40hp Johnson run

    that is what I call a waker upper ....!
  9. C

    You were right , she's a runner

    in my country you need a boat operator permit (unless it is a canoe or row boat ) and most idiots get it by passing a test behind a keyboard via Internet and if you can't read ,write or type your buddy can fill in the blanks for you.
  10. C

    1992 Evinrude 150hp EXEN will not run correctly

    slow mode aka SAFE mode on ETECs ...did that exist in 1992 ??? if so.... what triggers SLOW mode...best to find out as it will point the way to happiness
  11. C

    Points open to .035

    to check for sparks just use a drill to spin the fw while you ground the sparkplug to the engine body to at least confirm the presence of spark but an adjustable gap tester is even better has uggested. Suppose I should have ordered plug wires?... yes you should install new 7mm metallic...
  12. C

    Will Replacing Rings Increase Compression >105PSI?

    Engine runs really well but is slightly underpowered. hum... will a ring job provide a cost effective solution on a "really well running" 32 year old engine.
  13. C

    Will Replacing Rings Increase Compression >105PSI?

    are you having problems with th eengine ? is the gauge OK and accurate ??
  14. C

    Evinrude 7520 clearance question

    if you plan being addicted to oldies you should visit AOMCI ask a question board...where oldies are pampered :-) https://www.aomci.org/forums/forum/ask-a-member-d1/
  15. C

    Parts manual evinrude/johnson 7.5

    try this https://www.aomci.org/forums/topic/1956-johnson-ad-10-m-parts-list/
  16. C

    98 Johnson leaking hydraulic fluid.

    I find that a 1/4 inch impact screw driver works wonders on stuck bolts and screws start slow....
  17. C

    1992 Evinrude 150hp EXEN will not run correctly

    deleted
  18. C

    Lower unit oil

    I think BRP uses US size 5/32 Allen on OEM ...but I have managed to strip them. boils down to preferences I guess.
  19. C

    1992 Evinrude 150hp EXEN will not run correctly

    backtrack a bit.... how did all this start suddenly ? any chance fuel is inadequate (contaminated) for some reason ? any chance the VRO is not working properly, is it getting good pulses from the crankcase to work under load at higher RPMS . smokes a lot ...oilsmoke ( bad mixing) or...
  20. C

    Lower unit oil

    me.... I prefer slotted because hex heads are easy to strip... never went back to hex heads Trying to remove s tripped he head is a real pia.
Top