Search results

  1. C

    boat wanting to go left when cruising on water

    I believe some Bayliners with V-P outdrives have left handed props. You would adjust them the opposite way from MerCruisers, which have right handed props. Also trim position of the outdrive or outboard makes a difference. Have you tried trimming up?
  2. C

    Gelcoating keel

    Yes, the gelcoat will protect that area. A couple of coats of poly resin would protect it as well. You might add some colorant to either to help hide the damage.
  3. C

    Need ignition switch help

    I/Os usually need ign power to feed the CDI unit or coil. That serves as ign accessory on that ign switch, as they do not have a dedicated accessory wire.
  4. C

    Lost Keys for Older Boat

    If you do decide to change the ign keyswitch, and it is inside a MerControl, you will want to get an OEM or clone of the OEM switch, so it will fit inside the control. Not all will.
  5. C

    Need carb kit for 115 crossflow spl 1997 Johnson

    They should be avail from OEM, Sierra and likely GLM. Look up OEM part number on the crowleymarine site and then do a search on it.
  6. C

    1985 Mercury 85hp (4 cyl) runs great for 20 minutes then boggs down

    That temp switch is likely an overheat switch. They usually ground when the motor overheats. This ground completes a circuit that sounds a buzzer. You wire the ign accessory wire (battery positive, usually purple) to one side of the buzzer and the other side of the buzzer is connected to the...
  7. C

    1985 Mercury 85hp (4 cyl) runs great for 20 minutes then boggs down

    That motor likely doesn't have a thermostat. Most (not all) inline engines from that era don't have one. They rely on the waterpump to cool more than the motor requires. They therefore run dead cold at idle and warmer at cruise. If the prop pitch is too high or some other extra load is put...
  8. C

    Lost Keys for Older Boat

    Yes, there are only about 10 Mercury OB keys. If you open the control, the key code is usually written on the ign keyswitch. Alternatively, you can take the rig to the Mercury Dealer, and he will try each key until he finds a match.
  9. C

    New 150 HP Sea Pro

    OK, so motor is IL4, 3.0L, 4 cycle and 455 pounds. So 2 less cylinders than my 150HP 2.0L 2 cycle V6, and about 100 pounds heavier. Looks to be Mercury's answer to the real popular Yamaha IL4 150HP outboard. Those seem to be taking over, at least around here. The marketing is comical. That...
  10. C

    1974 850 mercury tilt cylinder leaking,

    Mercury used to sell a seal kit for the trim cylinders. The piston seal was teflon and required a special tool to install the piston and new seal into the cylinder. The rest of the seals were orings. If she is leaking around the trim rod, pull the end cap, pull the piston and cylinder out as...
  11. C

    1994 Ranger boat w/ 150 xri mercury.

    If it is inside the control, you need an exact replacement, so it will fit. Look on crowleymarine for the control that you have, by year, and get the ign switch part number. If on the dashboard, most any marine magneto-type switch will work.
  12. C

    Mercury sportjet 175 xr2 rectifier problem

    What year motor? Different years had different charging systems. Some had rectifiers, some had voltage regulators, some had both. Rectifiers blow when the battery and ground are not making a good connection with the rectifier.
  13. C

    Can anyone help me identify the brand of this hull?

    Looks like it says Elgin. The emblem looks like the Johnson one, and since Elgin is related to that..... Certainly from the 60's or early 70's.
  14. C

    1996 Ocean Runner 150 trim

    PTT units take Dextron auto trans fluid. Of course the OEM sells PTT fluid for it as well. Make sure the trim pivots are greased. Your motor will have two zerc fittings. You need to help the motor trim by hand, Using both your hands and PTT motor)until it is all the way up. Now use the...
  15. C

    What next? 90 hp Mariner

    Once the carbs clog, they do not unclog themselves. The carb clog can also cause the motor to run lean and hot, hence the compression test recommendation.
  16. C

    High RPM surge driving me nuts!!!

    Over oiling by the OMS pump is usually caused by an air leak on the gasoline side. I would check your fuel line for air leaks. Check the main strainer and make sure the seals and oring are good. Those motors were not designed for an electric fuel pump. You may be force-feeding the carbs or...
  17. C

    What next? 90 hp Mariner

    Your post said it run and then died and wouldn't restart. That is consistent with carbs becoming clogged, as junk is sucked into the carbs. Did I read it wrong?
  18. C

    What next? 90 hp Mariner

    So no gas from the carbs when pumping primer? That would indicate stuck float valves. Also, those particles can easily clog carbs. So if they came from the carb, it is time for cleaning and rebuild and new fuel line and filter.
  19. C

    1997 Merc. 40 HP Upper motor mounts

    Replacing the upper mounts is a major repair. You need to remove the gearcase and the powerhead. Then remove the exhaust extension to get to the mounts. You will need a powerhead base gasket and perhaps another gasket or two to reassemble. The mounting bolts usually need to be cut off...
  20. C

    No pee Johnson outboard

    Water pumps are kind of important. I would recommend a complete water pump kit with impeller, gaskets and housing. Sanding the impeller down probably doesn't give your the fine tolerance fit that is called for.
Top