Search results

  1. C

    82 Evinrude 70 hp

    yes pump must be FULLY immersed to pull in water... did you just do all this on a hose/muufs ?? Stationary operation of engine with garden hose ear muffs on keep RPMs low on muffs or in a deep bucket
  2. C

    Shop manuals - are they really different from year to year?

    You are welcome tube and google are good friends. just ask :-)
  3. C

    Shop manuals - are they really different from year to year?

    Leroy's site may help ... lots of info for you http://www.leeroysramblings.com/OMC_info/OMCinfo.htm it all depends on what you need to do to the engine crack it open or just basic upkeep maintenance
  4. C

    76 Evinrude 15Hp

    strange conclusion ... a bad plug is a bad plug maybe the plug boot connection was oxydized a bit and cleared up while reconnecting. I would be on the lookout for a return of the bug :-)
  5. C

    99 Evinrude 175 Ficht spark problem.

    see old search btw please post engine model # https://forums.iboats.com/threads/no-power-no-trim-motor-acts-like-battery-is-dead-even-though-it-has-a-full-charge.692994/
  6. C

    99 Evinrude 175 Ficht spark problem.

    before spending $$$$ on parts why not do a complete overall of electrical connection points. Any critical connection point with corrosion could drive you nuts I see that engine has a power dist panel PDP known to have a history bad (cold) solder spots on the main power input at the...
  7. C

    Retiring my Johnson '71 25hp

    Sad.... why not fix it somebody here must have parts and guidance for your issue. up to you ... you can buy a lot of gas and a spare fuel tank for what you will save on a good fix. how was compression ?
  8. C

    Johnson TN26 coil

    ms20,md20,hs20,hd20, ts-td20,and tn25-26.The OMC part#375189 see old post.. https://www.aomci.org/forums/topic/coils-for-tn-26-5hp-johnson/
  9. C

    1999 Evinrude (90 hp) E90FPLEEC - Runs fine at idle speed. But stalls when running about 3000 rpm

    good point .... had not noticed the injector in the parts diagram your the man...as always :)
  10. C

    78 Evinrude 9.9

    http://www.leeroysramblings.com/OMC_info/OMCinfo.htm
  11. C

    76 Evinrude 15Hp

    start by comparing the ohms value of the good coil (boot to engine frame) if identical suspect coil is likely OK if suspect coil checks out as OPEN (infinity) start by simply twisting the plug boot , wire and coil end connection RETEST boot to engine frame If OPEN (infinity)...
  12. C

    1999 Evinrude (90 hp) E90FPLEEC - Runs fine at idle speed. But stalls when running about 3000 rpm

    well there you go... better fix what ails it then ... Racerone.... any technical reason why premixing would not work .. be it 50/1 or 40/1 if the needed parts are truly NLA anywhere ? Is it the end fatality of the engine ?
  13. C

    1979 Evinrude 35 hp Water Pump Issue

    we love happy endings :-) :-)
  14. C

    Trim

    see pict. in the non operating mode both blue and green are grounded with either wire waiting for the other to flip to +12V thus reversing current flow to the trim motor
  15. C

    Trim

    or better said by the ETEC FOLKS.....
  16. C

    Trim

    green and blue motor works both ways so Voltage/current must be presented in alternate directions ..up or down since the motor can trim UP ok then both wires from the relays are ok and do pass juice to the motor because one wire has 12v and the other is grounded. In the...
  17. C

    1999 Evinrude (90 hp) E90FPLEEC - Runs fine at idle speed. But stalls when running about 3000 rpm

    first things first... up to you... .me I would just open the VST to check the vent float and needle. VST is just a can with a water coil to cool the fuel and let vapors escape via the top needle valve. they have been know to become stuck/rusty if the incoming fuel is contaminated with...
  18. C

    1979 Evinrude 35 hp Water Pump Issue

    3 inches underwater may not be enough to prime the pump properly . Remember the old farmer's hand pumps.... they needed a quart of water to start pulling water from the well. retest with the LU submerged and spin it with the drill to confirm the pump is pushing water out the pump body...
  19. C

    Temperature switch circuit 2000 Johnson 150hp

    If my compression readings are indeed low at 92-94psi would this not be enough to pulse the fuel pump causing it not to pump fuel? Actually compression#s inside cylinders have nothing to do with the vacum (crankcase pressure loss during the piston up stroke) inside the crankcase. the...
  20. C

    understanding idle on 1971 Johnson 50 hp

    to idle properly the idle circuit of the carb must be clean to allow proper fuel vapors to be generated by the upper part of the carb. If you feel adventurous pull the dime size plug on top (drill a small hole and use a nail to pop it out do not drill deep !! inspect /clean the small...
Top