Search results

  1. R

    I REALLY need input on a (just purchased, no history) OMC TurboJet 115 Initial startup and troubleshooting attempt.

    But the VRO does not put oil to the bearings directly.----The VRO mixed oil with the gasoline before it goes to the carburetors.
  2. R

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Fuel should not leak out the float bowl vent hole.----Need to inspect both carburetors I say.
  3. R

    Mercury 650 70’s outboard

    Just nuts and bolts.
  4. R

    Mercury 650 70’s outboard

    ???-----Poppit valve must open at higher throttle settings.----These 3 cylinder motors have enuff cooling issues already.----Do not ignore a leak there !
  5. R

    Mercury 650 70’s outboard

    Take the covers off.---Inspect parts.------Replace diaphragm and gaskets for the covers.
  6. R

    Mercury 650 70’s outboard

    There is a vent hole in some covers.----It allows the poppit diaphragm to move.----If water leaks out ,the diaphragm has a hole or is not sealed properly.
  7. R

    1987 Johnson 50 to 60

    Is one of those prop rated and the other one crank rated ??
  8. R

    4.5 mercury 2 stroke

    5 HP motors are used on 25" and 3000 LB sailboats to get in and out of the harbor.
  9. R

    Evinrude 50 rundown help

    Mix gas and oil at 50:1 on it.-----Operate bulb on hose till firm.----Raise fast idle lever.----Push key in and hold it in while cranking the motor over.-----Push key in as needed till motor warms a bit.----Do not let motor rev wildly in neutral.----Install a new water pump impeller and test the...
  10. R

    2000 70hp Evinrude 4 stroke. Thoughts

    Did you get an alarm on this Suzuki motor ?------Check lower unit oil.-----Check engine oil level ?----Did motor hit a submerged object ?
  11. R

    Engine building tip regarding gel-seal?

    Bolts will torque up.----Does not matter if anything is in the way !
  12. R

    Engine building tip regarding gel-seal?

    Absolutely no sealer to be used on upper and lower bearing housings !!
  13. R

    Buzzing in throttle housing '84 Johnson 90HP 4 cyl

    In 1970 they had the tiny red warning light on top of the control box.----Nobody can look at the control box all day.----In 1971 they installed the horn.
  14. R

    2004 Johnson 50hp buying advice

    Ignition parts is the least of worry.----Those gearcases are NOT robust in my opinion.----Ask seller about gearcase maintenance history.----Do a compression test.
  15. R

    Force 120hp won't start

    If the flywheel key is sheard the timing will be wrong.-----
  16. R

    Force 120hp won't start

    Pushing the key ( sluetel ) in and holding it in while cranking it over to start ?----Check the flywheel key too.
  17. R

    Evinrude 55 HP Running On 1 Cylinder

    No guessing or your part.---Best to check the fuel pump diaphragm !!
  18. R

    Water pump not pumping enough water

    Repeat.----Water needs to be 8" above the impeller.----Get a bigger bucket.
  19. R

    Water pump not pumping enough water

    I have never had to test a water pump with a drill in over 50 years.----When you are test running the motor is water 8" above the impeller ?
  20. R

    I REALLY need input on a (just purchased, no history) OMC TurboJet 115 Initial startup and troubleshooting attempt.

    Make sure the carburetor high speed jets are clean.-----They are inside the carburetor bowls.
Top