Search results

  1. R

    Evinrude 55 HP Running On 1 Cylinder

    Check the fuel pump diaphragm.
  2. R

    Water pump not pumping enough water

    Is water 8" above the impeller in your test bucket , yes or no?
  3. R

    Need help to id the motor

    I would not want that example of a motor on my boat !!
  4. R

    Need help to id the motor

    Given the thermostat location it is between a 1987 and a 1992 model.-----But I think that mess of a corroded motor needs a complete teardown and inspection.----It might even be hard to get all the bolts out.
  5. R

    Water pump not pumping enough water

    Did you use factory ( quality ) parts ?-----Is the motor overheating ?----Inspected / tested the thermostat ?
  6. R

    93 Johnson Distress Call

    Sometimes folks do not have the time to do it right the first time.-----But always find the time ( money ) to do it over again.
  7. R

    OMC Tiller motors

    I am sure there are some E-TEC tiller kits on the shelf somewhere.-----See one for 60,70 ,90 HP listed at only $1411.49
  8. R

    93 Johnson Distress Call

    These units are not robust !!----Gears / bearings on a 28 / 33 HP in the 60's were heftier than the needle bearings and teeth in these 40 / 50 HP ( propshaft rated ) motors.
  9. R

    93 Johnson Distress Call

    These gears need to be shimmed for proper mesh.----Shims are clearly shown in parts books.-----Dealer has a shimming kit and can do the driveshaft / pinion gear in minutes.----Good luck with it.
  10. R

    Low compression on top cylinder.

    All aluminum cylinder heads warp with time.-----A flat surface of glass / table saw can be used with emery cloth to true it up.-----Or valve grinding compound as well.----Never seen one that was not warped to some degree.
  11. R

    Carburetor's

    The 3 carburetors all operate the same and feed one cylinder.-----It is linkages / fuel connection that give them different part numbers.
  12. R

    OMC Tiller motors

    The market for big tillers varies.----Lobster fisherman , shell fish harvesters , native fishing people like these big tillers.----Depends on where you are.
  13. R

    Low compression on top cylinder.

    It is a shame that a mechanic / shop would quote for a rebuild without checking for blown head gasket.-----The head is warped.-----So refinish it and install a new head gasket.---Go boating.-----It might not hurt to tell the mechanic what you found.-----Might not treat you the same way next time.
  14. R

    Trailer winch bow anchor repair

    Put in a quality stainless bow eye.
  15. R

    1987 15hp Evinrude starts but quits every time.

    Start with posting compression test values.
  16. R

    Buzzing in throttle housing '84 Johnson 90HP 4 cyl

    Overheat warning buzzer.----Best look at the water pump first.----Failure to sort this out could lead to expensive new motor purchase.----Post compression test results.
  17. R

    Trim wiring.. 5 wire tt

    The little black wire and the white wire have to do with the trim gauge !----Trim / tilt will work fine with those little wires thrown on your garage floor !!
  18. R

    1975 9.9 sea horse

    Oil is put into the gas to lubricate the internals.-----Oil inside the engine is constantly replace with clean oil.----But oil in the gas is a big mystery for many folks.
  19. R

    Trim wiring.. 5 wire tt

    See post #3
  20. R

    1976 6hp Welsh Plug

    Your local lawnmower repair shop ( if you still have one locally ) might have a plug for $1.50 or so.
Top