Search results

  1. Scott06

    Duo Prop Removal

    Is one of these a left hand thread?
  2. Scott06

    Repair Y Pipe Possible?

    I have found the same bottom line Ebay wants folks to get what they pay for and use the platform. 99% of what i have bought off ebay is as advertised
  3. Scott06

    mercruiser 7.4 mpi can't figure out the ratio

    Agreed original numbers looked low. Hopefully just a valve job to fix
  4. Scott06

    Newbie looking for advice

    Read OPs first post
  5. Scott06

    Removal of bottom paint?

    Ok thats what i was thinking 2-4 mph loss. Mine is rough as hell. Its a 21 ft 3400 lb bowrider. I bought it with a cracked 4.3 low hours except for engine was in perfect shape. I put in a 5.0 partial engine from Michigan Motorz, essentially a new base engine with Edelbrock 1409 (in theory 260...
  6. Scott06

    Newbie looking for advice

    No i think it was lakes…i was thinking the same
  7. Scott06

    mercruiser 7.4 mpi can't figure out the ratio

    90 psi if accurate is a dead cylinder so yes would affect performance significantly. Would do a leakdown to see where you are loosing compression. Might be a head gasket or valve related vs needing bottom end rebuild. Have you had issues with exhaust leaking water into chambers ?
  8. Scott06

    Removal of bottom paint?

    most likely where ill end up… have done plenty of body resto work but never upside down on my back
  9. Scott06

    Removal of bottom paint?

    Thanks for replys, did you see any difference in performance after removal?
  10. Scott06

    Removal of bottom paint?

    I have a 2004 Sea Ray 200 sport. I bought it six years ago, previous owner had applied black bottom paint as it was slip kept in brackish water. Boat was rarely used as it only had 38 hours on it, Knucklehead didn’t winterize it so I bought it as a handyman special. The bottom paint looks to of...
  11. Scott06

    Revolution 4 XP prop

    Thanks for your comments. Understood about the pitch increments, i assume some of the difference in the XP vs the base rev 4 is tolerance to spec d pitch which i think in multiple engine offshore applications is more precise than my hacking around lakes…. yes i did use the PVS plugs, the mid...
  12. Scott06

    Revolution 4 XP prop

    Haven’t tried the ballistic yet , hear they are hit or mis depending on boat? You like them though? Revolution 4 gave me real good holeshot and best top speed. Its almost too much bite coming out if the hole for my engine, allows me to use full trim gets the hull out of water for slightly...
  13. Scott06

    Ran motor (in driveway) without oil in lower unit?

    My gen two has a bolt in front like the op shows in pics
  14. Scott06

    Brandnew retro fitted water shutters making tons of noise

    You would have a serpentine belt if it was a 96 and newer vortec head engine. How many bolts on the intake to head joints ? If you have 8 vertical it is a vortec ( valve covers said this in like 94) if u have 12 it does not have vortec heads. Possible you have a older block with v belt drive...
  15. Scott06

    Ran motor (in driveway) without oil in lower unit?

    If that is cut off , and you take the four on the sides off plus the one under the rear zinc should be no issue separating
  16. Scott06

    Ran motor (in driveway) without oil in lower unit?

    this above . Weld a nut to it a amazing how it will come off
  17. Scott06

    Newbie looking for advice

    except for draining cooling water in the fall no diff in mechanical ability between stern drive and modern OB. gear lube and oil changes basically the same way.
  18. Scott06

    Newbie looking for advice

    I see similar all the time these days, especially at bigger dealers in big boating areas. I have a '04 Sea Ray 200 Sport that I periodically peruse values to make sure my insured value is ok, I see listings for $13-22k. Not sure what folks are paying but listings OP mentions don't surprise me.
  19. Scott06

    Ran motor (in driveway) without oil in lower unit?

    post a picture of which bolt you are talking about , would think if the head is off you should be able to get it apart. Worst case take it to machine shop to drill and retap or helicoil
  20. Scott06

    Repair Y Pipe Possible?

    I once had this on Ebay with a non responsive seller, Ebay had to wait 'X" days before they got involved but eventually I got reimbursed, just a bit of a pain.
Top