Search results

  1. R

    primer bulb

    Agreed---Same mistake made on each carburetor.
  2. R

    Need help identifying a 85hp Johnson/Evinrude

    Post pictures of the actual power head.----Could be a 1969 ----to 1979 model.----Easy to pin point with pictures.
  3. R

    '88 Evinrude 90Hp not achieving WOT

    Lots of work and guessing done.----But step #1 is a compression test.----Post your values.----These motors are nearly world famous for broken piston rings.
  4. R

    1963 Johnson Super Seahorse 75hp Electramatic

    If it is an electramatic the throttle cable has nothing to do with the shifting.---NOTHING.------Find the wires going to the lower unit at the motor.----A green and blue.----Do an ohm check from green to ground.----Do an ohm check from blue to ground.----They should read the same.---Post your...
  5. R

    New points not gapping, 1957 Johnson 35hp Javelin

    Follow these steps.----Remove points. -----Back out the little cam screw 1 turn or a little more.---Install points-----TIGHTEN DOWN the screw with that special thin flat washer.----Yes tight.-----Rotate crankshaft to open points and adjust to 0.020" with the cam screw.------You now have them set.
  6. R

    1997 Johnson 70 hp water pump impeller o-ring

    Well, well----How about that.
  7. R

    Evinrude 60hp 1985 not starting

    Running on 100:1 is a huge mistake.----Just put on a new starter.
  8. R

    Need assistance. 1984 Evinrude 90 VRO V4

    There is a spot on the intake manifold near the starter motor. .----You put the 1983 model fuel pump there.----It mounts directly over the pulse port ( remove the plug first ) with a gasket and 2 screws ( 10-24 thread ) , then re-arrange hoses.----Plug VRO pulse port.
  9. R

    Original 1998 OMC 176615 Stainless Steel Boat Propeller- can it be rehubbed?

    Prop shops have the hubs and a hydraulic press to do the job.
  10. R

    Upper Crankshaft bearing below seal damaged

    Block will have to be split.
  11. R

    1999 Evinrude 90 V4

    There are no adjustable low speed mixture screws on this motor !
  12. R

    1985 Evinrude 185, 2 stroke, Engine shut off at idle (help)

    You have a bad gauge perhaps.----But I say pull the heads and inspect.----Sounds like a complete rebuild or new motor is in your future.
  13. R

    problems starting in the water

    The 100 / 80 PSI indicates that the cylinder head needs to come off.----Likely a scored piston / broken piston rings.-----Some will argue but this motor may need a rebuild.----Lucky you if it is a blown head gasket.
  14. R

    1974 Evinrude 85 HP cooling problems

    I do not believe there is a tell tale pisser on a 74 model.----Over heated ?----Post results of a compression test.
  15. R

    problems starting in the water

    Post the results of a compression test.-----Have battery charged and load tested.-----Inspect starter motor.
  16. R

    50hp Merc

    Well a Johnson outboard pump would work well if not better than the factory original.----I see nothing wrong in doing that.
  17. R

    Coils

    Some will argue.----I think compression should be around 140 PSI on that motor.
  18. R

    1988 Evinrude 50hp tilt relay

    No relay / solenoid shown for 1988 models.
  19. R

    1988 Evinrude 50hp tilt relay

    Not all of them used a solenoid or relay.-----Follow your wiring.----Sometimes a solenoid was only used for UP on those units.----Often that was mounted in a box on the inside of the transom.
  20. R

    Blew my Lower Unit I think (pics included). Need help replacing

    If they have to replace gears / bearings / shafts with factory parts , that sounds very fair
Top