Search results

  1. nola mike

    Fuel blockage

    Also, clear in line fuel filters are a no no on an I/o
  2. nola mike

    Mercruiser 3.0 unexplained rotational noise

    Even though the prop is the only additional thing turning in gear, you aren't under load in neutral (and you said you were testing in the water and not on land). Certainly possible for u joints or gimbal bearing to only make noise when a load is applied. Does it vary with Drive position...
  3. nola mike

    1986 mercruiser 140 3.0L

    Interesting. I would think that you'd fry the points and it would never run right. Thanks for the update
  4. nola mike

    Boat refueling

    These are submerged, no vapors to ignite. I'd at least do a marine fuel pump. I have regular jerry cans that i put vents into (you can buy 10 for $5 or something, drill a small hole in the can and pop them in). Use a large funnel, remove spout from jerry can and pour away. The vent makes the...
  5. nola mike

    Gimbal Bearing Noise?

    Some threaded rod, a couple of nuts and washers to use as a press. No. Moog 315g u-joints, I just ordered a couple off of amazon for $12 each Tube is easier to install, it's a bit louder
  6. nola mike

    Gimbal Bearing Noise?

    An allen wrench works fine on the hinge pins, they just need heat. The trim sender bolt sucks, but it is possible. Exhaust tube makes that part of the job a non issue.
  7. nola mike

    Gimbal Bearing Noise?

    Replace them.
  8. nola mike

    Clickity clack

    New to me outdrive, changed water pump, a seal, and ujoints at the start of season. Soon after had slight clicking on turns, has gotten worse. Pulled drive today... Yikes. It would appear that one of the clips came loose. Joint was contacting the inner surface of the large retainer nut. Glad I...
  9. nola mike

    Mercruiser 3.0 Stalling When Giving Gas in Forward Gear

    Meaning it's not closing when you throttle up in the water? Agree that this sounds like the issue.
  10. nola mike

    Electrical Issues - Help?

    I have a large screwdriver that serves that purpose on all solenoids and it's versatile enough to work on oil pressure switch as well. I have been thinking about throwing a relay somewhere on my ignition circuit. Rewiring the helm isn't going to happen, but there's so much potential for voltage...
  11. nola mike

    Electrical Issues - Help?

    You did that diode mod? I remember that thread, so cool
  12. nola mike

    '87 Merc 165 3.7 runs 20 minutes dies then hard to crank

    The water will leak past the rings if allowed to sit The blower running didn't actually affect the temp. If your wiring is older the extra resistance created by turning the blower on can make the gauge read higher. You didn't confirm if slow cranking was the problem?
  13. nola mike

    '87 Merc 165 3.7 runs 20 minutes dies then hard to crank

    The stat on that motor is 160, the gauge temp is notoriously inaccurate. Blower running will probably change what you're seeing on the gauge. Barely turn over like a dead battery? If so, first thing I'd check is water in the cylinders causing a hydrolock.
  14. nola mike

    Mercruiser 2.5 Alpha One gen 1 - running without exhaust bellows

    Do all of your bellows. If exhaust went, the others aren't far behind, which leads to major damage if you're lucky and a submarine if you're not.
  15. nola mike

    Electric fuel pump

    5-7 psi, but why?
  16. nola mike

    4.3L Front Engine mounts (old style) in Sea Ray Seville

    The stud should be at a right angle to the mount. It looks like you can push the new Mount forward and have it aligned with the holes, it isn't aligned with the rear either. That said, it certainly possible that the original mounts were not perfect, and the rubber took a set over time.
  17. nola mike

    1990 Mercruiser 350 Magnum Alpha One tune for altitude?

    Up to what point? You'll still be running with a less than ideal AF mix
  18. nola mike

    4.3LX acceleration opinions

    Or put the cooler on the bow...
  19. nola mike

    Possible boat purchase!

    It's worth more than 2k in parts.
  20. nola mike

    1990 Mercruiser 350 Magnum Alpha One tune for altitude?

    What carb do you have? The Weber/Edelbrock could be adjusted by changing the metering rods, which takes 5-10 minutes.
Top