Search results

  1. tpenfield

    Milky madness

    Just by the looks of the milkshake all over the engine and your description of 'blowing' the water out (which you now know didn't do anything except put some added wear on the impeller) - I'd say you have a total loss of an engine. Maybe it is just the exhaust manifolds that cracked and not the...
  2. tpenfield

    Bravo 2 outdrive not engaging when in gear

    Yes, you/he needs to check for missing parts. I assume he never found the impeller in the lower unit. :unsure: :rolleyes: I would also think you may want to take the outdrive apart again and put it back together with the aid of the service manual. Does your friend wish he waited until you...
  3. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    I'd prefer to do something like this, but I'll be taking a look at the boat first to make sure about all of the bits and pieces. On thing I am realizing is that the shift linkage and electrical box may have to mount to the riser instead of the elbow ??? :unsure: Not sure if they will raise...
  4. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    Thanks for the info, Scott. It looks like those are dry-joint style, but my manifolds are old school wet-joint.
  5. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    I found the information in my Merc manual (#16). It does show that the riser would be part of the sea water flow, but . . . I'm thinking it would be better to separate the iron (riser) and the stainless steel (elbow) for longevity. So, I probably will go with the 'second' style riser that I...
  6. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    Hi Scott, How much taller are the 8.1 elbows? I'm thinking I need about 3" of additional 'rise' to put things above spec.
  7. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    I’m going to try to get the second kind that allows flow between the channels and see if I can router the ducts between the channels to be a little deeper than they are originally. To your point, AD I want to have the most flow through these parts.
  8. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    I'm thinking that I'll be buying a 3/16" end mill bit . . . :D 🤪
  9. tpenfield

    Engine replacement

    Tranny??? . . . I don't see no tranny. Pull the outdrive, then pull the engine.
  10. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    I was thinking that, but still water would only go in the one channel and then up to the elbow. Ideally, I'd like the riser block to be part of the closed side, since the elbow is stainless steel. If I can't get the riser blocks with the ducts connecting the channels, then I probably would do...
  11. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    My take is the straight riser (first one shown) will only flow through 1 of the 4 channels. The other 3 channels have no way of passing water to the outlet fitting on the side of the riser block since there will be the block-of gasket at the top of the riser. Shown in red on my last picture...
  12. tpenfield

    Riser Extension Blocks - Full Closed Cooling ???

    Greetings, I have been wanting to add 3" riser extension blocks to my Mercruiser 7.4L engines exhaust, because the current setup is slightly below spec (1-2" low). Since I added an extended swim platform, the odds of sinking the stern lower with people is greater than before. Anyway - the...
  13. tpenfield

    Tahoe T16. Will it fit in my garage?

    A 'standard' 2-car garage might be 20', 22' or 24'. 24'4 is what may be more common :unsure: A tape measure would be the thing to use. Measure the inside length of the garage. Go measure the length of boat on the trailer (if you can). Also measure door width and height . . . same for the...
  14. tpenfield

    Tahoe T16. Will it fit in my garage?

    Welcome to iBoats . . . We don't know how big a garage you have. But the T16 is 16' 5" . . .add 2 feet at the stern for motor clearance and 4-6 feet at the bow for the trailer tongue and you've got in inside clearance requirement of 22.5 - 24.5 feet. A 'standard' garage is about 24 feet on...
  15. tpenfield

    Project with my sons

    Lots of restoration threads to review and learn from hereon iBoats. So,start reading. Look for local fiberglass wholesaler/retailer locations in your area (Google your way). Otherwise there are some sites ( US Composites being one of them ) that can ship you materials and supplies, but the...
  16. tpenfield

    Looking for first boat

    Newbies often under estimate the amount of boat they will need and various logistics of boating. Safety is paramount, so it is important to learn about boats and water safety. Filling a boat up to capacity is not all that safe for a new boater. Pontoon boats are often favored for larger...
  17. tpenfield

    Looking for first boat

    Pricey . . . but you will get that sort of thing from many boat dealers. nadaguides.com and bucvalu.com are websites that you can use to get an idea of market value. BUC is better than NADA, but cost about $20/month to subscribe - NADA is free and worth every penny 🤪
  18. tpenfield

    Looking for first boat

    Welcome to iBoats . . . What do you envision using the boat for/ Fishing? Water sports? Cruising? A mix of things? That will indicate what type of boat you should consider. Then it is a matter of age and brand to fit into your budget. Are you a good wrench turner? or not so much?
  19. tpenfield

    How long for water in an I/O to freeze?

    12 hours, 38 minutes and 22 seconds, or thereabouts 🤪 I'm with Bondo on this one , I'd say 6-12 hours in the mid 20's F will freeze the engine. Since the boat is inside a garage (unheated right?) that adds a variable, but the temp was 0˚ F - ish outside for a couple of days. . . I think...
  20. tpenfield

    Opinions on shop's quoted Bravo 3 maintenance cost

    IMO - the impeller sounds a bit high, unless they are replacing the pump body as well. The bellows does not sound too bad at all, but you did not mention if it was just the drive shaft bellows or if it included the shift cable bellows too. Exhaust should just be the tube (not bellows)
Top