Search results

  1. jerryjerry05

    power tilt & trim

    Re: power tilt & trim I have the trim and tilt parts but not the pump. You'll need a motor and a thrust bracket and misc.bolts and nuts.
  2. jerryjerry05

    1999 Force 120 Problems

    Re: 1999 Force 120 Problems Leaking fuel when ideling,could be the floats off?? Or the reeds are broken in that carb. The air screw,put it back where it was. Can't remember?Start at 1 turn out and then adjust It shouldn't have anything to do with gas comming out the front. Manual? Look on...
  3. jerryjerry05

    Welsh plug sealer.

    Re: Welsh plug sealer. Let me get my bag packed!!! Bling for my motor!!!! I like it!!! I've got 6 carbs!! http://www.amazon.com/Permatex-20539-Indian-Shellac-Compound/dp/B0008KLOG6/ref=sr_1_1?ie=UTF8&qid=1344340520&sr=8-1&keywords=indian+shelac
  4. jerryjerry05

    125 Force Ignition Question

    Re: 125 Force Ignition Question Any water in #4 or on the plug? Start it and while it's running pull the plug wire. See if it makes a difference. Than swap the coil around. The ground might be loose too.J
  5. jerryjerry05

    Hey JB

    Hey JB if you read this. They post so many Johnson/Evinrude post on here. Ever think about maybe breaking it down into 2 sections? One for the under 40 and the rest in the other. You can post a thread and it goes to 3 pages by night fall.J
  6. jerryjerry05

    1972 Evinrude electric shift.

    Re: 1972 Evinrude electric shift. Sorry usually have all that in there. Its an 85hp and it's a 72 85293R J02966 Thanks.
  7. jerryjerry05

    trim/tilt 1987 force help locate fluid cap

    Re: trim/tilt 1987 force help locate fluid cap Screw /cap on the side of the pump housing.
  8. jerryjerry05

    1986 85 HP Force Lower Unit Drain Plug missing?????????

    Re: 1986 85 HP Force Lower Unit Drain Plug missing????????? Drain plug on the very bottom. Allen head screw.Maybe covered with paint?? The slotted screw is for the shifter linkage. DON"T TOUCH!!!!!!!!!!!VERY IMPORTANT!!!!!!!!
  9. jerryjerry05

    Newb questions on 100HP 72' Johnson

    Re: Newb questions on 100HP 72' Johnson Bendix staying up is normal. Cold results are almost identical to hot. Finger tight. How many revs did you let the motor turn? You should let it turn until the guage stops going up. Very important to have a HOT battery. You need to ground the plug wires...
  10. jerryjerry05

    1992 force 120hp L drive on a 19.5 Bayliner. very low power, only about 5 mph

    Re: 1992 force 120hp L drive on a 19.5 Bayliner. very low power, only about 5 mph First thing to do is change all the wire connectors on the stator,trigger and both packs. Then change start it. See if that makes a change. No change move switch box/pack around and see if it changes position...
  11. jerryjerry05

    1972 Evinrude electric shift.

    Just got my 1972 Evinrude Electric shift running(YEA!!!) Gonna scrap the boat(83junk). Started fair after 6years of setting. Even shifts the way it's supposed to. Comp 120 all 4 Was wondering if I sell it for parts what's it worth.
  12. jerryjerry05

    I'm back. I really thought I was done. I should've known better. Force 120 LU ??

    Re: I'm back. I really thought I was done. I should've known better. Force 120 LU I'm waiting!!!Got a space reserved with your name on it!!! Try this,drop the lower,from the rear of the unit. Install the prop,lift the right blade of the prop up, turn shift shaft rod to the left, it should...
  13. jerryjerry05

    Yet another stuck steering tube! Make sure I'm thinking right, please.

    Re: Yet another stuck steering tube! Make sure I'm thinking right, please. This is the broken jaw(puller) he was talking about. Broke it trying to remove a flywheel. That outfit will lift a cat diesel!!!! A 4x4 is plenty strong.
  14. jerryjerry05

    Yet another stuck steering tube! Make sure I'm thinking right, please.

    Re: Yet another stuck steering tube! Make sure I'm thinking right, please. This is all you need. Any hardware store. If you take it off you will loose the pivot point and have no place to push pull??? But if you take it off you will open a new can of worms. It's been in salt water it's...
  15. jerryjerry05

    Timing at idle speed?

    Re: Timing at idle speed? You pull all the plugs when you did the test? A screw in tester or a push in? Screwin is by far better! It's a wonder it starts at all??? Remove all the plugs. Key OFF use a jumper box on the solenoid.. Throttle open all the way. Screw in tester and turn over till...
  16. jerryjerry05

    Timing at idle speed?

    Re: Timing at idle speed? The pics are of the wires I fixed up to ground out the plugs for testing. (I just did the static timing as you suggested. However after setting my light to 28 and adjusting the screw till the TDC lines up with timing line it runs worse and won't stay started when...
  17. jerryjerry05

    1997 force 120 starting problems

    Re: 1997 force 120 starting problems Pics are from a GOOD starter. Guy couldn't understand why it wouldn't turn the motor?? 15year old starter???Take it apart and check for crap/corrosion. Remove the plugs and see if it turns over?? Then do a compression test. Still trouble turning over...
  18. jerryjerry05

    Know anything about a Force 125 flywheel?

    Re: Know anything about a Force 125 flywheel? Picture? The only thing under the flywheel is the exciter for the trigger. It's held together with 2 pins.See pics. If these came apart then you need a new wheel.J
  19. jerryjerry05

    Not a puzzler NOW!!Here's a puzzler???

    88/85Force.Good compression. I'm setting up a block I had in the shed and put a complete(supposed to be good) wiring wiring system on the motor. Everything went on right and I have spark. I checked TDC and it's right.I have the tool for finding it. On the flywheel it's the single hash mark a...
  20. jerryjerry05

    1999 force 90hp gear linkage help!

    Re: 1999 force 90hp gear linkage help! In forward gear,turning the motor clockwise the prop should turn clockwise. Take the lower unit off,put in a stand or block it up. Pliers or vicegrips on the shift shaft. Try spinning the prop and turning the shift shaft. There should be 3 definate...
Top