Search results

  1. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    more info... https://forums.iboats.com/threads/1998-ficht-115-diode-number-or-spec-pn-0583898.664083/ https://www.cdielectronics.com/ficht/ a love story... read it all especially post#26 onward :-) and post #33 http://www.bbcboards.net/showthread.php?t=504541&page=2
  2. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    check everything assoc. with power relay feed source, 10 amp fuse contacts and the fuse itself (try another one) pdd contacts to fuel pump etc... hold the key at START while DEAD .... have a buddy tap the PDP panel gently but smartly
  3. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    see modern 200 hp etec layout
  4. C

    Evinrude 60Hp - wont stay running, help!

    In short, the motor starts right up, ?? does it just spin the engine or do you actually get ignition explosions while the starter turns the engine over ? . If so I think it is unlikley the kill wire (s) are grounded their role being to kill the ignition not the starter . As I...
  5. C

    1974 Evinrude 25hp wont run.

    before blowing $$$$ in suspected air leaks just wrap them up in cellophane tightly to prevent air leaks ... retry . you must be the unluckiest man in the oldies world at 130 posts ...:-)
  6. C

    1988 Johnson 15hp throttle cable retaining clip reinstall?

    deleted
  7. C

    1988 Johnson 15hp throttle cable retaining clip reinstall?

  8. C

    1990 evinrude 70hp boggs down at high speed

    maybe in here ? https://www.cdielectronics.com/wp-content/uploads/2013/03/CDI-Electronics-DVA-Charts.pdf?msclkid=da30c920c55e11ec819d0cfe0be40a4a
  9. C

    1974 Evinrude 25hp wont run.

    "The one thing I have found out is if you buy cheap you get cheap" agree 100% yet... I try to balance things between cheap and fleeced .
  10. C

    Tilt and Trim Seal Kit Help

    ask the folks here on IBOATS
  11. C

    1990 evinrude 70hp boggs down at high speed

    agree... yet carb is an easy first try.... before the big $$$ kick in
  12. C

    1990 evinrude 70hp boggs down at high speed

    how long ago was the carb job done...you may want to ask the mecanic why all his work does not allow anything above 2500 rpm . was the engine tested in any way after his work you paid for ?? tank venting ok ? fuel supply restricted somehow ? old style carb you could always try a blast of...
  13. C

    head & exhaust plate gasket replacement - 1970 4hp

    I dont apply sealants... orient the cyl head gasket top tab with the engine casing tab torque to specs .... retorque to specs after a good run is what I do . I do not use thread lock (blue) just some commom yellow teflon tape
  14. C

    1974 Evinrude 25hp wont run.

    i did, it does spit fuel in a good flow. looks like it is working OK better to look for another cause. hook up a small fuel supply directly above & into the carb inlet nipple and see if the engine runs with the new source of fuel. if it does not then the problem is...
  15. C

    1988 Johnson 8hp can anyone tell me what the head bolts torque is please

    well 60-84 inch/lb is 5-7 foot/pounds you an check the web for standard bolt side torques
  16. C

    1974 Evinrude 25hp wont run.

    see info ... http://www.leeroysramblings.com/Rebuilding_fuelpump.htm read 3 times...then proceed to rebuilding :) why not just disconnect at the carb...spin the engine to see if pump is or is not pumping out fuel
  17. C

    1988 Johnson 8hp can anyone tell me what the head bolts torque is please

    see pic for older engines but close enough I guess see qd fd
  18. C

    33 hp Johnson no spark

    black wires probably going to safety features ex: round vacum cut out or neutral safety feature grounding the wires kills the points/sparks so leave them ungrounded for now
  19. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    when you find it and if no obvious flaws shows up follow the main power wire (See diagram ) directed to the ECM and go measure the B+ voltage at the ECM . while you are at it why not power everything down.... open up the main connectors to the ECM and check for...
  20. C

    1976 evinrude 6hp won't idle

    basic carb bugs . yours has no adjustable needle at the bottom it is a fixed jet behind a 7/16 nut... just remove the nut and blast away with carb cleaner DO NOT DAMAGE the jet with a metal poker ....use mono filament line to push out any crud if any blast all orifices with air (...
Top