Search results

  1. alldodge

    Boating Trim - electrical problem

    What motor do you have? If it's a Mercruiser then most likely the trim limit switch on the port side of the gimbal ring
  2. alldodge

    1990 4.3 block and 1995 heads, which rocker tightening specs to follow?

    I have to agree, unless the push rods and rockers are changed they will be different length from the vortec IMO
  3. alldodge

    '09 Merc 5.0L Carb / Alpha 1 - Engine runs and will not respond to ignition or kill switch when at temperature?

    Block diagram
  4. alldodge

    Inboard Drive Shaft Issue I need Help!

    Don't think it's the drive or the shaft, it's the coupling alignment. IB need to be aligned to within .003 MAX Many folks that do alignments don't do it correctly
  5. alldodge

    Low fuel pressure, fuel filter half full while idling.

    WADR - Motor mount doesn't need to be removed. The bracket that holds CF module is held on by 2 motor mount bolt studs. The nuts and washers are removed which releases the bracket that holds CF module.
  6. alldodge

    Low fuel pressure, fuel filter half full while idling.

    Either need to find a skinny person or stuff has to be removed. It's a B***h but it's also a boat. Suggest start by removing the exhaust manifold. After removing clamps and pipes, remove the outer most bolts holding the manifold. Take bolt to hardware store and get about 18 inches of all...
  7. alldodge

    REPLACING SERPENTINE BELT ON VOLVO PENTA 5.7 GI - 300 - J (WITH AUTO TENSIONER)

    Would be easier to post pic of your tensioner. There are a few different ones, and they either need a square drive extension or a wrench to release tension
  8. alldodge

    Mercruiser outdrive gasket

    One of the 2 surfaces is not flat, must have a very slight tapper. Look at this thread by @Rick Stephens and how he does his https://forums.iboats.com/threads/bellhousing-gasket-squeezing-out.670419/
  9. alldodge

    Mercruiser outdrive gasket

    Bummer, don't know why I was seeing transom when you even said bellhousing Sorry It is going on dry?
  10. alldodge

    Mercruiser outdrive gasket

    Check to see if your transom meets spec and it's going on dry
  11. alldodge

    warning alarm wont stop beeping

    I don't know your motor, so this is just info For the alarm to sound it needs 12V (purple) on one side and ground on the other. The ground side goes to a sensor which will ground when (for example) the motor overheats. The alarm should have 12V applied when key is ON which sounds like it is...
  12. alldodge

    mercruiser 5.7 350/260hp alpha one outdrive starting issues

    Start by verifying spark, use a spark tester to verify length and color Is the gas old? Use a gas can and fresh gas and a piece of gas line into the can. Try to get all old gas out of filter and carb. Smell the gas and does it small like gas or something else?
  13. alldodge

    Circuit breaker

    I don't know, I would hope if this was posted in the Yam section one of those folks might know. If you know what size your alternator is may just go maybe 10 amps higher
  14. alldodge

    Raw water pump

    I would get kit 807151A14 and replace it every 2 to 3 seasons
  15. alldodge

    Adding fuse panel question

    With no more then your going to have, 8 gauge is great but 10 would be more then enough, but just my opinion
  16. alldodge

    Circuit breaker

    Would help to know what motor? Is it the main feed to the helm or somewhere else?
  17. alldodge

    Brand new cranking battery at 4.7 volts

    Something is draining the Bat. Bilge pump maybe, not running but pulling power
  18. alldodge

    Low fuel pressure, fuel filter half full while idling.

    The first pic shows the 2 lines going in/out This pic shows the box it's in
  19. alldodge

    Ideas on getting lake water temp sensor w/o drilling into hull?

    Had one in my younger days. Like I really want bend down and wait, I'm old, not going to happen
  20. alldodge

    AGM Starting Battery

    Yep'er same as LA type, no issues
Top