Search results

  1. alldodge

    How to remove Helm Lid

    Will be today or tomorrow. Adjusted the lift Thursday but now need longer bunk boards. The local lift guy said he will bring them today, but this is the same guy that I waited 3 years to get him to do another adjustment. I gave up and adjusted my self, then the next week he shows up, go...
  2. alldodge

    How to remove Helm Lid

    Don't know didn't ask Adding stuff to a new boat always takes place fire extinguisher, vhf, other things. Don't see any issue so long as what was added did not cause a problem, if it does it's my fault My Rinker has a lanyard but I stopped using it. I stood up beside the seat and killed the...
  3. alldodge

    How to remove Helm Lid

    Found it, Its VV 403 https://www.sbmar.com/wp-content/uploads/2018/03/VesselView403-Installation-Instructions.pdf
  4. alldodge

    How to remove Helm Lid

    Chap said to remove the bezel on the smartcraft gauge which will give access to screws hold gauge in. Once removed will have access to screws holding top. I'm looking for the install instructions for the gauge installed, it's square. I didn't get manuals for it so it's starting to take some...
  5. alldodge

    How to remove Helm Lid

    Your probably right, I'll try that
  6. alldodge

    How to remove Helm Lid

    No good Looking under the front lip I can find nothing In the head found a overhead panel which when removed showed nothing to help. It showed there is a full fiberglass wall between it and the top. I'm back to thinking there is some sort of spring latch I'm sure missing Formula :(
  7. alldodge

    Trim Manual

    Look in 14 for A1 G2
  8. alldodge

    Mercury 350 MPI beeping every few minutes

    Need to have the motor scanned for codes. Dealer or use Rinda https://www.rinda.com/
  9. alldodge

    Trim Manual

    About everyone of them
  10. alldodge

    Low fuel pressure, fuel filter half full while idling.

    Might be the regulator or the pump Could remove the return line coming from the Reg at the fuel filter head. Plug the filter head and hose end, then just key ON a couple times (do not start) to see if pressure builds above 40 psi. It should go close to 60 If it does increase, remove Regulator...
  11. alldodge

    How to remove Helm Lid

    I need to get behind it to install 1st Mate FOB kill switch
  12. alldodge

    How to remove Helm Lid

    Never thought there might be screws under the front lip, will have a closer look tomorrow
  13. alldodge

    How to remove Helm Lid

    Z-bracket? and don't see screws Just looked up Z bracket
  14. alldodge

    How to remove Helm Lid

    No, behind it is the toilet and solid fiberglass wall I can push the left or right side and it moves back in a twist, this is why I'm thinking it's some kind of a latch. Might take some kind of body tool like a car
  15. alldodge

    How to remove Helm Lid

    Chap 280 OSX Trying to remove the Lid which covers the helm. No room under it, and can bearly see panels and displayes are bolted from behind Can move the top a bit and think its held in place by a spring latch. Might be like a dash on a car
  16. alldodge

    Best type of fuel tank for gas engines?

    Suggest plastic or aluminum If your doing a Original Restro so it will be worth more, then need to do original Can find many premade tanks, just need to find one that will work close enough
  17. alldodge

    V Drive trans oil analysis 1999 380 DA

    No expert on oil analysis, but ... if the prior buyer backed out so this would tell me that the Trans needs rebuilding, and probably needs both done. Use that info to determine your price and if you still want to buy it
  18. alldodge

    Stalling and Starting problems

    Here ya go. This first pic is where to adjust float level when upside down. The float drop bends float arm. Be careful bending
  19. alldodge

    Stalling and Starting problems

    Will dig them up later and post if someone else doesn't The top of the carb comes off to adjust. Upside down for float level and right side up for float drop
  20. alldodge

    Stalling and Starting problems

    Float level not set correctly which causes flooding
Top