Search results

  1. R

    88 mercury 80hp ELPTO general info

    It has the plastic gear on the crankshaft.------It is easy for you to compare the parts on these motors.-----I know what you find about the parts.
  2. R

    1967 Johnson 6hp prop

    If in Canada---------evinrudeparts.ca-----Might possibly help finding a used one.
  3. R

    1972 Grew SS245

    That was a factory unit to run / flush off a garden hose.-----Cap it off with bits from your local hardware / CTC store.
  4. R

    88 mercury 80hp 3 cylinder not charging

    Same parts as clearly stated.----Same displacement.-----Minor changes and decals !
  5. R

    88 mercury 80hp 3 cylinder not charging

    ??----It was the same parts for many years.----Only a few years with the 80 HP decal.-----Marketing 101 in my opinion.
  6. R

    88 mercury 80hp 3 cylinder not charging

    No the stator also provides input for ignition.-----Do an ohm test on stator battery charging windings , the yellow wires I believe.
  7. R

    Evinrude 25202r no spark

    The fuel pumps are very reliable.-----Lots are replaced as a guess.-----Look for wiring that is grounded somewhere.----Post a picture of you coils.
  8. R

    1996 Johnson 40hp No Spark

    I think 96 was the first year without the red plug.---------Near impossible to give advice on 12 volts / wiring from 1000 miles away.-----You need a factory manual with wiring diagram.
  9. R

    What type of hydraulic fluid to use in '98 50hp Johnson? Replace relays too while I'm at it?

    Top up the fluid and test.-----Does the trim motor work / sound normal both for up and down ?
  10. R

    Rebuilding a Johnson 10hp QD-16

    I am rebuilding a 1963 model this fall.-----I have many 10 HP models.----I recommend that you fit the 61 / 62 / 63 model rods and pistons.----End of the story.
  11. R

    Rebuilding a Johnson 10hp QD-16

    Read post #2 carefully.
  12. R

    Rebuilding a Johnson 10hp QD-16

    I would install the rods and pistons from a 61 / 62 / 63 model 10 HP.----Much better with a hefty bearing on the wrist pin.----Same bearing as used on a 125 HP V-4 model.
  13. R

    Looking for Service manual for 1982 evinrude 2hp (E2RCNE) outboard

    Counting all the needle bearings and not losing them is the only challenge.------Pretty simple motor.---Trick might be to take rings off the piston and taking assembly out through the crankcase.------I have manuals but not needed for these wee ones.
  14. R

    Any lower unit experts?

    Was this a new factory lower unit ?----Aftermarket ??
  15. R

    98 60 HP ELPTO lower unit

    Normal to click in forward when turning prop clockwise.
  16. R

    Strange leak on 9.9 Johnson

    That " leakage " might be normal.
  17. R

    Only getting spark in one cylinder

    Some will argue.----Charge the battery.-----Have the battery load tested even if new.-----Take starter apart for inspection / ohm test on armature / possibly new brushes.----Not much money spent.-----I agree , low cranking speed leads to a " no spark " condition.
  18. R

    Looking for Service manual for 1982 evinrude 2hp (E2RCNE) outboard

    A 1980 manual will do.-----These were essentially the same from 1968 to about 1990.----Some very minor differences.
  19. R

    2020 9.9 CT engine stalls

    Run fuel out of carburetor when done boating !----An empty carburetor stays clean.-----Tiny passageways on 4 strokes can be restricted by fuel forming gummy deposits.
  20. R

    Carburetor Rebuild Question....V4 Crossflow

    A bit low in my opinion.
Top