Search results

  1. alldodge

    Bravo I, II & III interchangeability question

    From your previous post your needing the bell housing (part of the transom assembly), and yes most any can be used with one caveat. On top of the face or the housing look for slots on the top. The slots are there so the U bolts do not come in contact when fully raised. You can use the one...
  2. alldodge

    trim/tilt line leak repair help

    Appears so, you know more then I. This kind of lines the O ring does the sealing but nut has to be tight. Th
  3. alldodge

    2001 sea Doo GTX RFI

    From looking at the manual it shows a Black/Pink and Purple/Pink wires feeding the pump. Guessing from the colors I would say Purple/Pink is hot and the other is grounded by the computer to turn it on
  4. alldodge

    Click but no start

    Howdy, we need to know what motor your working on (merc, VP, 3.0, 5.7 etc)? Once we know we will have a better idea of how to fix it and maybe GA_Boater will move it to that section Is the battery fully charged and measuring between 12.5 to 12.7 volts? Are the battery cables clean at both...
  5. alldodge

    water not draining in engine compartment

    I doubt if there is a drain. Most cases it gets drained when the boat leans enough to dump it in the bilge. Here's mine (not a searay) on the starboard side, and it use to be flat until I did transom repair
  6. alldodge

    Mercruiser 555 - ECM no power?

    Sure looks like the same ground, note splice 104 on letter m which is everywhere CAN, sensor and ignition
  7. alldodge

    Mercruiser 555 - ECM no power?

    Yes your thinking correctly, in typing I switched the tags, its correct in post 6
  8. alldodge

    454 MAG. BRAVO MPI (GEN VI) GM 454 V-8 1997 Crank No Spark

    If your meter is good, the 12.3V is barely on the good side, and a bit low. Should run if it ever starts
  9. alldodge

    454 MAG. BRAVO MPI (GEN VI) GM 454 V-8 1997 Crank No Spark

    Removing the red kills all power to the coil so there will be no spark Code 33 is MAP voltage high, so disconnect MAP connector and measure voltage on Lt Green and Gray. The MAP will not keep the motor from firing Check out your distributor
  10. alldodge

    Octagon Window and Siding

    Nope, not what I'm looking for, that is they make a piece and then you cut to fit. I have a brake and can bend my own aluminum, so I can make brick molding. The brick molding in the link does not cover the inside of the frame. In pic below, blurry on left is current window, and one on left is...
  11. alldodge

    Octagon Window and Siding

    Getting the materials together to vinyl side our rental house. The house has 2 octagon non-opening windows. They are wood and the molding extends out more the the J-channel. I want to cover all the wood I can to seal it up, and I have a aluminum brake. I can bend 8 pieces on metal, and try to...
  12. alldodge

    Crankshaft position sensor replacement

    The CPS is the same part number for both motors that use a Cam sensor and ones like yours which do not. Backfiring and having trouble to idle would have me also looking at timing, IAC and distributor cap. You mentioned that the distributor cap was replaced, and if the motor has the same issues...
  13. alldodge

    Rocker switch panel

    You can feed all the switches with a buss bar, and have a separate fuss for each one
  14. alldodge

    mercruiser 4.3l??

    Might have popped the 50 amp breaker, use a voltmeter and check for power
  15. alldodge

    4.3 GL starving for fuel

    If you have a local auto store might be able to get a vacuum/fuel pump test gauge as a loaner. Then need Merc tool or similar 91-81078 (cost $36) https://www.walmart.com/ip/New-Mercury-Mercruiser-Quicksilver-Oem-Part-91-18078-Tool/853659979 Could also remove the fuel line between the pump...
  16. alldodge

    Freshwater Prop Anode Info Needed

    Good info, thanks Now need to understand the differences between the postings and Merc corrosion manual http://www.boatfix.com/merc/Techbk/97/97hs7.pdf Merc says for fresh water and mercathode mounted on the bottom of the transom assembly, readings should be 620 - 1180 Millivolts with Digital...
  17. alldodge

    3-blade vs 4-blade

    I also think tabs would help very much, but as a current owner of a 232, installing tabs would not gain much benefit IMO. The reason being is there is no room to place them where they would be needed close to the outside. Installing them close to the drive would bring its own problems and don't...
  18. alldodge

    Crankshaft position sensor replacement

    Test procedure
  19. alldodge

    Tabman

    Just read on the Formula Forum that Tabman passed away recently. Didn't get any details, but he will be missed
  20. alldodge

    R.I.P. iboats Member Tabman

    Just read on the Formula Forum that Tabman passed away recently. Didn't get any details, but he will be missed
Top