Search results

  1. alldodge

    How to Repair Cool Fuel stud

    Pulled it out, and it is a plastic box mounted to a 1/8 plate with 4 each 1/4 28 hex socket screws. Used a cut off tool to cut it flush. Drilled 7/32 hole and tapped for 1/4 28 Now to decide if I want to order a brass stud from McMaster 47 cents (with shipping probably $5 bucks), or use...
  2. alldodge

    Rebuild trim cilinders

    The trim limit is 21 3/4 max, can be less (If you don't need it to go all the way up, for trailering and such, I would make it a bit less). The dimension can be found in manual 28 on page 5D-8 and manual 11 on page 4A-17 The check balls stop fluid from returning. Doing this holds the piston...
  3. alldodge

    Bought a 1998 Sea Ray Sundancer 270 wide beam with rot...

    I fiber glassed it back into place. The inside has a full length mirror which went back in once glassed, so that took care of the inside. The engine compartment has the heat and sound shield which is glued in on that side. You can see the shield used
  4. alldodge

    Bought a 1998 Sea Ray Sundancer 270 wide beam with rot...

    A couple of pics Before the bulk head was removed After bulk head was removed Here is other pics
  5. alldodge

    How to Repair Cool Fuel stud

    Doing some work and was reinstalling the bracket on the cool fuel module. Still using one finger to tighten and the stud snapped off. Tired of feeling like a pretzel, I took a pic and got out. Looking at the listing I don't see where the studs are part of...
  6. alldodge

    Change to High Volume Oil Filtration

    Feel like a pretzel but the new lines are on. Still need to install and wire the new gauge. One of these days I'm going to redesign the helm layout and probably get rid of the speed-o
  7. alldodge

    Can you identify this boat?

    You may still be able to find a kit, or look on wood boat sites and find one close to it. Found these being made in the UK. Change the seats and it would be real close
  8. alldodge

    Outdrive wont turn fully to port

    Not bad, I like her I use to ride around on a red hull, but she was an ice breaker.
  9. alldodge

    Where is the starter relay

    From what I'm finding is your starter relay is square, and should be on top the motor. Looks like a small square box and same as the fuel pump relay
  10. alldodge

    Hardin bravoitis kit install

    I would assume the brass brush would be used to clean the hole out, using a drill. The hose is inserted into the bell housing, then the plastic piece is inserted using the tool with a 3/8 extension. I have never used silicone on these parts. silicone will cause them to slide even when dry...
  11. alldodge

    Bravo 3 Trim sender

    The Org/Blue goes to the 10 pin connector (Analog) The Org/White goes to connecter B-13 (Digital) Black is ground Here is a short vid on connecting to smartcraft monitor That said your using analog gauges with smartcarft monitor. To use analog gauges I think your going to need to get a...
  12. alldodge

    08 350 Mag MPI: No Spark & Negative Turning Tach While Cranking. Banging My Head Against The Wall

    Are you getting 12V at the coil Pink/Wht pin C-A ?
  13. alldodge

    Parallel Batteries to Solenoid

    Yes there are marine rated solenoids and they "look" just like the one installed. My Formula has two of them, one for combining batteries, and one to operate the wench. They are rated for continuous duty, but they never are turned on and left on. Google 24213-BX The battery one should be...
  14. alldodge

    Parallel Batteries to Solenoid

    The solenoid is used to combine the batteries together if the one battery will not start the motor. My formula uses the same thing, and there is a switch up by the key switch that is pressed if needed. The solenoid is an easier way to combine and is momentary where a battery switch is done...
  15. alldodge

    Hull Supports?

    The box is there to transfer the load over a wider area. It needs support from one side to the other to keep the boat from squeezing together. When filled with foam it becomes more ridged. If you just went straight across in front of the tank then there is just two points to hold the sides...
  16. alldodge

    Little help, I'm stuck on the water.

    If your talking about parts in item 14, this is the needle seat assembly. If that is the case it needs cleaned out real good and replaced
  17. alldodge

    Little help, I'm stuck on the water.

    The vid is showing me that your flooding, and is caused by curd in the needle seat or the float sank, my guess is crud. The best method to fix temporary, is remove the top of the carb, should be 7 screws. Then remove float and needle, clean out then reinstall. Another possible option is pump...
  18. alldodge

    Trim sensor wiring

    OK then yours would be like this The limit is on the port side and the gauge is on starboard. It doesn't matter which of the black wires coming from the limit or sender is connected to which other wire.
  19. alldodge

    Trim sensor wiring

    Being a 1988 I'm thinking you have two solenoids, so here is the diagram If you have only one solenoid let us know Edit: woops you said two solenoid in first post
  20. alldodge

    1989 waverunner 500 water in cylinders

    Your not going to suck water in from the exhaust with a 2-stroke. The read valves allow air and fuel mix to be drawn thru the intake, around the crankshaft (to lube crank) then up into the cylinder to burn. The burn gases are expelled when the cylinder starts back down. Your water can be...
Top