Search results

  1. alldodge

    No fuel on 120 (2.5l)

    Here is my tank, it has 90 degree fittings welded to the tank. The valves are screwed into those fittings. If yours are different maybe a pic would help
  2. alldodge

    New Project - 1978 Terry Sun-Sport

    Looks like a complete gut. I would suggest getting a full face mask, the glass dust can mess with your eyes I got one like this but not at this price http://www.uline.com/Product/Detail/...Q&gclsrc=aw.ds
  3. alldodge

    Transom Repair - Uneven after grinding

    Note to remember, final thickness needs to be 2 to 2 1/4 inch where the transom assembly bolts up.
  4. alldodge

    Bravo 3 bellow sleeve.

    Howdy Magnus The sleeve should slide over the boot end and be flush with it. If the boot is positioned as shown in the pic below, the sleeve should side on with soap.
  5. alldodge

    Mercury 90 Fourstroke not charging all the time.

    Not an outboard guy but sounds like it's working. The standard Merc alt will not start putting out full charge until rpms come up. Here is the test and output curve Here is the manual http://boatinfo.no/lib/mercury/manuals/75-90.html#/122
  6. alldodge

    mercruiser 7.4 mpi cold start stalling

    Are you sure your on J2 ?
  7. alldodge

    mercruiser 7.4 mpi cold start stalling

    Have to apologize, here I thought I posted all the pages then see I didn't. My only flimsy excuse is doing to many things at once. Here is the first part of checking the connections and resistance values at the sensor. You shouldn't need to remove the sensor to test. Now you should be getting...
  8. alldodge

    mercruiser 7.4 mpi cold start stalling

    Looks like I missed part of the testing, the 4V is a bit high so try this part
  9. alldodge

    Cracked exhaust manifold = milky oil

    If there is a hole thru to the water jacket, sure water can come in there. Is this the spot your talking about? Now if you have batwing style exhaust manifolds, these have caused many issues with hydrolock and water intrusion. This is for 4.3 but same style for V8
  10. alldodge

    mercruiser 7.4 mpi cold start stalling

    Don't bother with the MAP, don't see how it will effect what your seeing. I'm thinking the Engine Coolant Temp (ECT) sensor or the connection to it is the problem. Below is how to test the circuit and you will need a test light and Volt Ohm meter. You don't need to remove the sensor to test...
  11. alldodge

    1990 SeaRay Sundancer 310 Complete Rebuild advice needed

    It is a pain and can get toward the lower end, but take your time and note what adjustment has what effect. I said .002 but it should be no more then .003 on an inch. The adjustment is close to the same but can vary a bit if your prop shaft goes completely thru the trans coupling instead of just...
  12. alldodge

    98 Rinker captiva 232 for $500.Should I do it? pics

    It's a roll of the dice. I would pull some plugs and see what they look like. Also is a saltwater boat, so that brings it's own issues. IMO the 5.0 EFI will still not be enough motor to have it move like you may like, but will work, hope it comes with a bravo 3. Last thing is the boat...
  13. alldodge

    Electric fuel pump interrupt

    Lets try this; during cranking the motor, power comes from the starter connection to the pump. After the motor starts, key is released and power is removed from the pur/yel from the starter, engine is running off fuel left in the carb. When oil pressure builds up, oil pressure switch is...
  14. alldodge

    Electric fuel pump interrupt

    Yes..... and ..... No Yes you can use the beeper circuit but you have to be on the positive side of the beeper/horn, basically your attaching to the purple wire. If you connect to the other side power goes thru the beeper before it gets to the pump.
  15. alldodge

    Mercruiser 454 computers

    My guess would be you have a MEFI 3 being your listed model year. So far as the map tuning, normally I wouldn't think it would be that much off. If it was placed in a real light speed boat, someone might have monkeyed with the turning. Even with that it should be able to push 300 plus HP. I...
  16. alldodge

    Sae J1171 Marine

    Left is trim tabs, middle is outdrive lube bottle.
  17. alldodge

    throttle bracket

    Maybe something like this https://www.holley.com/products/fuel_systems/carburetor_components/brackets_and_linkage/parts/6035
  18. alldodge

    Yamaha Trim and Tilt Gauge

    Not a Yam guy but found this info, hope it helps http://boatinfo.no/lib/yamaha/manuals/1984-1996yamaha.html#/552 Sender is item 26 red and gauge is item 22 blue
  19. alldodge

    After 22 years and this is all

    Pull the shift lever out enough to remove the cotter pin Then push link bar and latch forward and pull it out Here are all the pieces, o-ring on top and seal on bottom. Popped the bottom seal out with a small flat tip Now just need to clean them up and wait for parts to come in. I keep...
  20. alldodge

    After 22 years and this is all

    Use 3/6 hex wrench and remove the shift fork and shift lever Once screws are out use the top screw and thread into top of shift shaft Normally you can take pliers or even just you firgers to lift it out. I used a pry bar and just lightly bounced it on both sides due to the rust on the bottom.
Top