Search results

  1. alldodge

    2005 Tahoe Q4 assistance

    No biggy Brian, we see it every now and then and most will repost to fill in the blanks for others watching. Its all one big mushy mess around here but we like it :) This might help
  2. alldodge

    3.0 liter holley carb questions

    I think your talking about the pump over ride setting as in pic below. Are you holding the throttle in the wide open position and the pump rod should be fully compressed when measuring?
  3. alldodge

    Chrylser 105 Conqurer

    Stripped everything out of it, only thing left is a bit of sanding and wire brush then start putting it back together. This is the largest piece of the two stringers, about 5 inch wide. After the stringers were removed Now the keel Boat sure wobbles a lot now. Going to have to make...
  4. alldodge

    350 mag efi, high idle 1300rpm and low top speed

    With your TBI systems and a TB-V ignition putting your engine in base timing is done a bit different. Need to connect a jumper wire to the Purple/White wire (No 13) to a good ground. While in base timing mode also adjust idle to 600 rpm, do this sitting in the water
  5. alldodge

    Carver 3607 1982

    You can use either Automatic Charge Relays (ACR) or an isolator to charge the house batteries. Stating you have three house batteries you might just want to wait until you can plug your battery charger in. The typical alternator max output is 65amps. most lead acid batteries, even deep cycle...
  6. alldodge

    2011 6.2L Mag Keep getting alarm mostly at idle

    Agree don't change your stainless pump housing, the dealer is either not to bright or just wanting to make some more money. The pressure switches seam to have a lot of trouble with them over time. There is a thread here which goes into the switch itself and discussion of bypassing, but I have...
  7. alldodge

    Need advice on transducer placement on a flat bottom skiff

    Don't install it close to your engines prop wash
  8. alldodge

    350 mag efi, high idle 1300rpm and low top speed

    Howdy The idle is controlled by the ECM and is not adjustable, but 1300 is way to high. I wonder if someone left the engine in base timing mode. Look for the DLC connector and see if it has a jumper wire on it or another connector on it. If there is no connector or jumper, disconnect the...
  9. alldodge

    What happened to the beeper

    Thanks, I have manual 23 and have been looking at it. I have had both harness replaced, engine and Fuel injection with MEFI-3. The difference I have yet to be able to determine is the engine to MPI connector. Manual 23 shows one connector and there is a different number of wires being shown...
  10. alldodge

    Outdrive will not lift or tilt or go down

    Did you do this stripping at the throttle control? Much easier to do this at the pump. Have you checked the fuse?
  11. alldodge

    How is the trim limit switch supposed to function?

    Howdy Darren Your correct, if the trim systems is connected and working correctly the trim button only allows it to go up a given distance. Here is a link to the trim system http://web.cemr.wvu.edu/~mathews/boa...20Eighteen.PDF And a pic
  12. alldodge

    What happened to the beeper

    Talking about my Formula with the 502. Originally had a MEFI-1 and a direct connection (tan/Blue) from the warning horn (beeper) to the Temp and oil pressure switches and the drive lube bottle. When switch closed the horn would sound. Today, up graded to the MEFI-3 and now all these same...
  13. alldodge

    Propeller hub kit for 1968 Mark Twain with MC-1 outdrive?

    Went to a place called Mercstuff and found the following
  14. alldodge

    Carver 3607 1982

    Try this way Select send to server and then wait until the window changes back to main screen. Can take a bit depending on file size. If pic is to large you need to resize or use photobucket or such
  15. alldodge

    Mercruiser Power Steering Woes - Lots of reads, pics, and a video!

    The flats do need to be up and down, otherwise the valve doesn't line up correctly
  16. alldodge

    Power steering issue...Goes full right..

    Sounds to me that someone didn't install the steering ram cable correctly. I would suggest removing the steering cable nut and cable. Make sure the flats on the cylinder are straight up and down. Install the cable and tighten the nut while keeping the flats held securely. Have wheel and drive...
  17. alldodge

    bottom paint?

    That's gelcoat, and appears to me that who ever did the job did not do it correctly. This is why the paint is peeling. The good news it's peeling, the bad is it needs to all come off so it can be barrier coated first before, bottom paint
  18. alldodge

    Chrylser 105 Conqurer

    Starting to look like the stringers will not be saved, or very little of them. The more I moved to the stern the heavier the foam was with more water. Can really see why Chrysler never made it as a boat manufacture, the boat was built pretty flimsy. Only cross support there was a six wide...
  19. alldodge

    Chrylser 105 Conqurer

    Did a bit of demo
  20. alldodge

    shift interrupter

    Appears you should have one, its item 30 in the link below http://www.mercruiserparts.com/Show_Pictures3.asp?dnbr=56999&ivar=images/CRUISER/56999/6.png&inbr=1574&bnbr=20&bdesc=TRANSOM+PLATE+AND+SHIFT+LEVER This part is no longer available and if it has gone bad it may have been removed. Its on...
Top