Search results

  1. M

    Engine Mount Installation Tool

    Lol 😆 sorry mu goof 🤪 yes almost half inch.. I swear I had it right in my head ....
  2. M

    Engine Mount Installation Tool

    Ok do I reached out to the manufacturer of the tool they saidvthey don't sell the shims independently of the tool but they did tell me that the shims are .450. So almost an inch..
  3. M

    1999 75hp Fuel Prime Issue

    It definitely sounds like the fuel pump .. have you checked the fuel pressure?
  4. M

    Engine Mount Installation Tool

    Yeah I wish I had access to the stringers on both sides but it's a finished deck and no way to access the back side of stringers unless I cut access holes in the deck and dig out some foam..
  5. M

    Engine Mount Installation Tool

    This will not be the alignment stage. I am replacing a 3.0 with a v6 so this will be for getting the engine beds right. It's alot easier for 1 person to manage a 20 pound tool then it is to move an engine host around with an engine on it in the dirt if you know what I mean ...
  6. M

    Engine Mount Installation Tool

    Yup I seen page 4 where it talks about using the spacers.. but it doesn't list the spacers anywhere that has the tool available to sell so I was thinking the tool in the installation sheet may be a newer tool and and the was hoping the spacers where not required for the tool I have .
  7. M

    Engine Mount Installation Tool

    So I bought an engine mount installation tool.. I got it used after receiving the tool and looking up at the instructions for the tool it seems that I need spacers that come with the tool but when looking the tool up there is no mention of the spacers at all does anyone have any experience with...
  8. M

    Gear lube reservoir

    Because if you do it this way it will trap air in the lower and eat up the bearings and gears in the lower before the air makes its way to the top.. Always fill from the lower .
  9. M

    is the CDI for 2001 90 hp elpt 4 mercury same one in 2002 f80 yamaha?

    I would venture to say it's the same cdi / pcm hardware but unless it can be programed to your engine and you have the ability to do it then I would say your out of luck on that
  10. M

    is the CDI for 2001 90 hp elpt 4 mercury same one in 2002 f80 yamaha?

    I don't see how those 2 parts are interchangeable...
  11. M

    1991 mercury 115hp 2 stroke gauges?

    I agree with Chris on the selection of gauges...
  12. M

    1991 mercury 115hp 2 stroke gauges?

    What Guage's are you looking for?
  13. M

    Motor revs up but doesn’t go anywhere?

    You can get that prop for about 50-60 bucks. Look up how to tell if prop is slipping to confirm its the prop ( which it probably is ) or take it to a shop that's your options..
  14. M

    1983 black max 150 running poor

    Seen this to many times .. raise engine up take the fuel line going to the carburetors off the pump and plug the pump then pump the bulb and see if fuel comes from the carburetors if it does then its a fuel pump issue...
  15. M

    2 cycle 9.8 water pump question

    Should be a double lipped seal or 2 seals on both housing since it needs to block fluid from both sides.. In which case it wouldn't matter which way it was facing because it seals from both sides
  16. M

    2008 250 optimax pro XS steady beep

    Yes I've disconnected them it didn't change anything... and the manual says it would be 4 beeps for oil are water this is a continuous beep beep beep ...
  17. M

    2008 250 optimax pro XS steady beep

    I have a 2008 250 optimax pro with a steady beep as soo. As the engine starts its a non stop beep .. beep beep beep ........... I have checked the oil sensor and the water separator sensor and there fine I'm thinking I need to check the code so my question is will the Rinda Technology scan tool...
  18. M

    Aftermarket carbs?

    Mike's Carburetor Parts www.carburetor-parts.xxx He even has a video but most 3.0 issues ive delt with not idling below 1000 rpm have been due to flooding ( which could be fuel pump ) are vacuum leak
  19. M

    1994 evinrude 150 emptying carburetor bowls then dies

    Ok so it's all fixed the issue ended up being trash in the pump, and the float height in the vapor separator was way to high..
  20. M

    1994 evinrude 150 emptying carburetor bowls then dies

    Yeah I found the VRO pump I just couldn't wrap my head around how it worked and the manual real doesn't explain it much..but here's how I think it works The VRO pump creates a vacuum in the vapor separator chamber which draws fuel into the chamber where the vapor is removed from the fuel then...
Top