Search results

  1. M

    1994 evinrude 150 emptying carburetor bowls then dies

    Ok so working on model number J150jlera. If I pump the bulb until it's hard it will start and run then after running a few minutes idling it will bog and cut off and won't start until I pump the bulb again. My gut is telling me fuel pump but I see there's what's called a vapor pump. Is this...
  2. M

    Alpha 1 gen 1 water pump

    I normally go oem as well but the owner of the boat didn't want to spring for the extra $45 for the base and he didn't have any info on previous service so I kind of insisted on replacing the whole pump assembly
  3. M

    Mercruiser outdrive gasket

    Yes it is. I did try using perfect seal once but learned that was a mistake 😕
  4. M

    Mercruiser outdrive gasket

    This is the gasket I'm referring to... for the Bell Housing
  5. M

    Mercruiser outdrive gasket

    I've always cleaned the area good with razer and brake cleaner. Should I lightly sand the area. Keep in mind this has happened on more then 1 occasion and on multiple drives.. I'm sure it's something I am doing are could do different I was just looking for suggestions..
  6. M

    Mercruiser outdrive gasket

    Has anyone else had issues with the Bell Housing gasket pushing out when torqued to specs ( mainly on the right side looking at the unit) I always use OEM gasket for this but no matter what it always pushs out some times more then others.... Thanks Mark
  7. M

    Alpha 1 gen 1 water pump

    I'm replacing the water pump in an 1988 Alpha 1 gen 1 serial number 0c501178. When I go to the parts look up it gives me several kits. I believe the kit I need is 18-3319 ( I would go OEM but they dont list a kit with the base.. ) When I look at the Sierra catalog it list part number 18-3320...
  8. M

    Cracked my out drive need help on a replacement

    It's a 1990 1.98:1 gear ratio..
  9. M

    Mercruiser Carb with 3.0 engine Alpha 1 is running a little rich. Do I go in or out with screw?

    Then yes in / clockwise would be leaner also while it's running look in the carburetor and make sure there's no fuel dripping from the top .. fuel pump could have to much pressure, fuel pump diaphragm could be leaking and sending fuel up through the clear / yellow hose to top of carburetor or...
  10. M

    Mercruiser Carb with 3.0 engine Alpha 1 is running a little rich. Do I go in or out with screw?

    Smells rich at idle?
  11. M

    Trim Manual

    Well there you go now I have a manual that can be labeled as Mercruiser Trim manual Thanks
  12. M

    Trim Manual

    I am talking about the drive trim system ( pump and rams ) I was speaking of the remote control for the shifting and throttle. I was just making a general statement, ( I know they have a separate manual for the controllers ) This statement was just to say they had a separate manual for the...
  13. M

    Trim Manual

    Makes since for it to be in the drive manual I guess since that's where I would look for the parts lookup. Thanks
  14. M

    Trim Manual

    I'm not working on anything at the moment I was just asking a general question on what manual would be considered the manual for the power trim. I know they have a separate manual for the controllers and I didn't remember ever seeing one for the trim so I asked.
  15. M

    Trim Manual

    Here are snippets from service manuals 18 and 25 neither of them have it.
  16. M

    Trim Manual

    Ok so quick question what manual has the trim trouble shooting and repair info in it ? Thanks Mark
  17. M

    Clicking tilt trim and now blowing fuse ? 50 Mercury 2 stroke

    Pump locked up or bad motor possibly..does it do it up and down. ?
  18. M

    Difference between 1997 & 1998 90hp 2 stroke outboard

    The welch plug should look something like this and located on top of the cylinder head
  19. M

    Trim Pump Fluid

    I use ATF or hydraulic fluid in mine never had an issue
  20. M

    1992 Mercury 60HP 2stroke Constant Alarm

    Your assumption would be correct it is the for speed odometer and the warning module is for the oiler as well if it's still being used then replace it ( if you premix the gas ) then toss the module
Top