Search results

  1. kramerpage

    4.3L 807166A3 Water Shutter Replacement question/issue

    I replaced my water shutters last night and I'm not happy with the results. I sanded the interior area around the old shaft hole. Then cleaned with throttle cleaner and applied a thin coat of molly assembly lube. My issue it that one of them doesn't always freely close. It gets hung up on its...
  2. kramerpage

    1989 4.3L Heater core hook up locations

    Can someone tell me where to hook up the two heater core lines to a 4.3L. The hoses are 5/8 inch. I have not purchased any fittings for the motor yet. Thanks
  3. kramerpage

    4.3L Exhaust Manifold inspection methods / replacement

    I have two sets of exhaust manifold assemblies. One set that's on the motor that will go into the restored My Rotten Lady and one set that came from the donor boat. I am wondering with both sets from 1989 and both ran in freshwater only. Do I need to be concerned? Is there an inspection method...
  4. kramerpage

    need help with motor ID for parts and shop manual

    Guys I need help identifying this serial number for a 260 4 barrel 1983 v8. I need parts breakdown for repairs and also need to know which number mercruiser shop manual to buy. Sterndrive.cc serial is B420705 which is not the original drive. Need the same info for it. Thanks so much
  5. kramerpage

    quicksilver throttle shifter disassembly

    I need to remove this from the plywood trim. Is there a diagram or disassembly instructions? Thank you
  6. kramerpage

    need NEW pulleys 4.3 L

    Looking for new WP pulley part 15120 it's 5 1/2 in dia. Also looking for engine crank pulley 90081-C. My sheaves are worn. Need PS and ALT pulley but I don't have them in hand for part numbers. Seams like I install belts every year. Thanks aliment and tension is good btw. Engine serial...
  7. kramerpage

    take a look. Engine mount... how can I be efficient?

    This removal is going super slow. I cut the entire perimeter with disk to wood. Beat it with a sledge. Then cut off just small box at Mount. This stuff is tough as nails. Many nails and 3 inch long staples. Staples are rigid. Nails are also. I'm just picking at it slowly with claw on 16 oz frame...
  8. kramerpage

    hydraulic lines thru transom question

    I need to run hydo lines from distribution manifold on gimbal plate thru gimble housing on a 1989 alpha. The merc manual says nothing about it #6. One hose has a taller 90 degree bend. Can you tell me does the taller hose go fwd or aft? I'm guessing aft. Thanks.
  9. kramerpage

    I screwed up ground wire install

    Can I drill and tap the gimbal ring on the outside cause I don't wanna take off the bell housing to screw in the screw? It's all about continuity.... Geeeee Whizz
  10. kramerpage

    alpha shift cable install two grommets? ?

    Read the #6 manual and cannot find the instructions for these two items. OEM merc lower shift cable kit. # OC735235 gimble. Thanks guys
  11. kramerpage

    service manual needed for repair

    Hello all I need an engine manual for a 4.3 L 1989 #0C616538. I purchased a number 25 OEM manual on ebay inwhich I quickly found out its the incorrect manual. Learning pains. Thanks so much. I just need to know what number it is. I've narrowed it to a # 7 but don't want to make the same...
  12. kramerpage

    fluid type motor mount leaking???

    I was cleaning up my motor mounts and noticed a small amount of red sticky fluid at the weep hole on one of the mounts at the bottom underneath the mount. I understand these are the fluid type of motor mount. How do I know if they are good or bad. I believe they are none serviceable. These came...
  13. kramerpage

    Alpha Christmas in July !#!#!

    Well its all here on Monday. Funny how the United States Post Office works. 13 packages in all. Some ordered almost 2 weeks ago....Hmmmm Now I can get to work and put this resto build to rest.
  14. kramerpage

    alpha reassemble sequences question

    From reading the manual several times I'm still vague on the sequence. This is for Alpha off the boat on a bench. Attach 3/4 water hose to plastic fitting above gimbal bearing completed Install trim senders completed Install shift cable bellows completed Install exhaust bellows gimbal side...
  15. kramerpage

    alpha 3/4 water hose length question again

    Guys I bought the mercruiser OEM seal kit and it came withe two size water hose. I have established I need the 3/4 inch. Now I have read many post on this forum and others to cut the hose. Yikes!!!!! My hose is 14 and 1/8 long OEM mercruiser part. Actually it's a Parker series 7095 mpt 300 psi...
  16. kramerpage

    waiting on parts...before . during progress

    Well I'm still waiting on my shift shaft bushings for the bell housing. Here's a before / during pic. Ready to get this thing done....
  17. kramerpage

    perma-lube gimbal bearings do not need seal

    perma-lube gimbal bearings do not need grease retention seal in front of bearing. Wish I knew that. Spent 20 on seal and 45 on seal mandrel kit.
  18. kramerpage

    alpha steering shaft seal install battle

    So I went to install my new seal and found that there are three small ears on the bore below the bushing which I did not replace. So the seal would not install from below going up into the housing. I then filed the ears off and coated the bore and seal with perfect seal. It is correctly seated...
  19. kramerpage

    Can you rebuild alpha on bench?

    Now that I have all the components blasted and painted. Can I 100 percent rebuild the gimbal housing gimbal ring and bell housing on the bench. I am replacing every single component with OEM. It's seems it may be awkward not mounted on the boat. May be easier I just don't know cause I have never...
  20. kramerpage

    ??painted drive shaft bellows mounting surface??

    The paint shop painted the mounting surface for the drive shaft , shift cable, and exhaust bellows. It's beautiful BUT.... Seams to me that's not good for the continuity wire on the drive shaft bellows. Do I need to sand the whole sealing surface down or just where the continuity clips are on...
Top