Search results

  1. C

    Stop switch location?

    The keyswitch does have two M terminals. One has a white wire that goes directly to the wiring terminal block on the engine marked Magneto. The other wire is blue and it also goes to a 2nd terminal block on the engine marked Magneto. If I'm understanding you correctly, I should have a second...
  2. C

    Stop switch location?

    I have a 1988, 125hp Force outboard. Don't know any history on it, other then it sat for years. Had no key for the ignition switch when I bought it and purchased a new ignition switch online. Had it fire up briefly before I installed the new igniton by jumping the solenoid. On a side note, the...
  3. C

    125 Force ignition wiring?

    Thank you, Nordin. After cleaning up a bit of corrosion and hooking up the wires as you indicated, I was able to get the switch to work properly!
  4. C

    125 Force ignition wiring?

    Thanks much! I'll give it a try tomorrow.
  5. C

    125 Force ignition wiring?

    Greetings. Recently picked up a 1988, 125hp, Force on a junk Bayliner. The ignition switch was missing. It's a remote ignition on the dash. I picked up a new ignition switch but could use some help as to where the wires go. I checked several sites but didn't come up with an answer. All of...
  6. C

    No Spark 1971 Evinrude 60hp

    Thank you for that info.
  7. C

    No Spark 1971 Evinrude 60hp

    Glad I wasn't your neighbor! 😊
  8. C

    No Spark 1971 Evinrude 60hp

    I was told by a marine mechanic that this motor can be started without the large plug being connected and by disconnecting it and jumping the starter, if you get spark the problem is in your ignition. When I had the plug connected, I was getting 12 volts to the amplifier
  9. C

    No Spark 1971 Evinrude 60hp

    Thank you
  10. C

    No Spark 1971 Evinrude 60hp

    Thank you
  11. C

    No Spark 1971 Evinrude 60hp

    Thank you
  12. C

    No Spark 1971 Evinrude 60hp

    Recently picked up a 1971 Evinrude 60hp, model #60173C. I have no history on it. Motor turns over freely with about 150 compression on all cylinders. Motor has no spark. I've replaced the coil and cleaned and gapped the points to .010. I've tried starting the motor by disconnecting the...
  13. C

    How to synchronize carbs?

    I have a 2001, 80hp carbureted 4 stroke Yamaha. Can someone direct me to the procedure for synchronizing the carbs? Put fresh plugs in it and after one season they are all carboned up. Thanks
  14. C

    Impeller kit number?

    I'll have to check and see. Thanks for the info!
  15. C

    I want to add a third toon of smaller diameter

    Yeah, I just might do that. Thanks
  16. C

    I want to add a third toon of smaller diameter

    Thanks
  17. C

    I want to add a third toon of smaller diameter

    Thanks. Makes sense. Just thought I'd ask since I already have the smaller toon. I'll just continue my search for a 23inch toon.
  18. C

    I want to add a third toon of smaller diameter

    My goal was to get input from someone that has experience with a smaller center toon. Thanks for your input though. You certainly live up to your nickname. Merry Christmas!
  19. C

    I want to add a third toon of smaller diameter

    I have never seen one smaller either but I'm hoping there's someone on this forum that has experience with it. As far as a larger one in the center, I'm familiar with that. My brother had a Manitou tri-toon and the center toon was larger, or at least it hung lower in the water. However, when...
  20. C

    Impeller kit number?

    Do these older Johnsons have an alarm to let you know if the VRO stops working? That seems to be everybody's concern.
Top