Search results

  1. C

    1969 evinrude 25 horse 2 stroke won’t start

    electric choke solenoid to close the chke when starting carb... did you remove the top plug and clean the LS cct.??? verify the side channel feeding fuel to the top idle needle... the side channel is very narrow if plugged no fuel will rise to the top idle needle . did you gently.... try...
  2. C

    1969 evinrude 25 horse 2 stroke won’t start

    so it runs with starter fluid ...then you have sparks ...good ! time to clean the carb again. did you remove the top plug to clean the LS circuit drip holes, passages leading to them etc.... starting is usually involves pulling fuel from the top LS circuit with the throttle plate...
  3. C

    How to get my throttle roller closer to the armature/flywheel?

    the screw does not look maxed out much ?? I see lots of threads to go further ??
  4. C

    Intermittent Start - Starflite 75

    always use solid wire ... never carbon
  5. C

    Old Johnson 3hp

    thanks for your feedback and PROOF that properly cleaning carbs is always a good thing !
  6. C

    Loss of power, won't plane

    lots of charts on the web on torque charts...should be close enough
  7. C

    Tilt of my outboard not locking

    a 12 inch long ... 1 inch dowel attached to the rear transom (inside) works good and you wont loose it. !
  8. C

    Intermittent Start - Starflite 75

    I have used similar ones on my oldies and they work fine.
  9. C

    9.5 Evenrude

    start with this.... clean the carb .. it must be 100% clean!! http://www.leeroysramblings.com/OMC_9.5.htm
  10. C

    Fuel pump for 6hp 6904E

    blow which direction..?? install it with mounting bolts tight see was happens .
  11. C

    25hp Johnson won't start

    point must open at TDC ..something mecanical is needs a deep look into. did you change the condenser ..yes no ?
  12. C

    25hp Johnson won't start

    he replaced points and coils I am certain a missing or broken key would habe been noticed no ?
  13. C

    25hp Johnson won't start

    some points .. bad ones.... have appeared in recent years whereby the pivot arm rubbing on the cam lobe is not the proper length. There is no reason to have an off-set from the highest point of the lobe and TDC....reverify your points to ensure you are using the proper ones.
  14. C

    1993 Evinrude 30 HP tiller pull start

    classifiedst AOMCI may help
  15. C

    1977 Johnson 35 - Won't start

    https://www.bing.com/videos/search?q=utube++johnson+35hp+1977++no+start&&view=detail&mid=D107BA7FCDB7C395745DD107BA7FCDB7C395745D&&FORM=VRDGAR&ru=%2Fvideos%2Fsearch%3Fq%3Dutube%2520%2520johnson%252035hp%25201977%2520%2520no%2520start%26qs%3Dn%26form%3DQBVDMH%26%3D%2525eG%25C3%25A9rer%2520votre%25...
  16. C

    1977 Johnson 35 - Won't start

    https://i2.wp.com/www.maxrules.com/graphics/omc/wiring/77-78_55HP.jpg in the 55hp version the solenoid is locally grounded and the neutral switch is in series from the key'S START post. not much to stop 12v from reacing the solenoid control prost other rtan broken wires, fuse or defctive...
  17. C

    1977 Johnson 35 - Won't start

    Don't worry they told me I was color blind at my local Telco hiring office.. not good for splicing cable pairs..... so they kept me away from fixing color coded cables/pairs :) but I still worked 30 years there :) wiring is usuall y the least of problems :) but yes it can be a...
  18. C

    1977 Johnson 35 - Won't start

    ground wires are usually black power wires are usually red sometimes purple from the switch START post so don't apply power to black wires. you have to learn to use a volt ohm meter if you plan servicing your oldy post a color photo close up of your solenoid wires. but do easy...
  19. C

    1977 Johnson 35 - Won't start

    to test the solenoid " locally" just use a pieceof wire and link the entry 12v from the battery and touch the small control post on the solenoid.... one post goes to ground so be carefull. the control post from the key is the one you needto energize. if the ground part of the solenoid...
  20. C

    1977 Johnson 35 - Won't start

    solenoid need power to close the starter circuit and be grounded first thing to check before spending $$$ is to check if volatge is presented to the solenoid with the key at start... power to the solenoid from the key may be interrupted by the neutral switch. key the key on START and...
Top