Search results

  1. C

    2006 Evinrude ETEC 50 Cowling & Side Covers Year Alternatives

    bummer... ETEC plastics are $$$$$$$ if you have all the parts you may be able to have them repaired in a body shop for less cost (they can weld some plastcis) . I was able to reglue my 5-6 cracked bolt mounts on my 75 ETEC all depends on how bad that storm was.
  2. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    also this link and info If cranking voltage drops too low the ECU will go offline and you will lose laptop communications to diagnostics. It only connects diagnostics when you are in the ignition position or cranking...
  3. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    found this ... maybe.... go to the link and read all of it https://www.thehulltruth.com/boating-forum/996809-evinrude-ficht-intermittent-no-start-solved.html Evinrude Ficht: Intermittent No-Start SOLVED I have a 2000 Evinrude Ficht 200 HP that had a nagging, annoying intermittent problem...
  4. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    Been reading all this again... ok I had missed the fact you said T&T works.... the engine runs fine so ECM works and it is not a HOT ECM issue causing the problem ODD that the speed of turning the key ON impacts the starting logic incl the starter that seems to stop for a few minutes...
  5. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    I do not think the EMM would talk back to EV diag. if it was not powered ... if or when your ignition " times"....... out hopefully it is not a basic wire problem.... you should at a minimum ascertain what happens to the 12v supplied to your ECM . Unfortunately I do not have a wire...
  6. C

    1987 Johnson 50HP cooling route

    have you considered changing impeller maybe thermostat before heading into other issues ?
  7. C

    Evinrude 6hp gear shifter out of alignment

    if so the next step is to pull the power head like done for an impeller job on a 5.5.hp ....not a big job anyway. see around time mark at 00. 40 sec. take care not to damage the base gasket. if you do.... order the correct one because base gasket patterns differ. you could always cut...
  8. C

    2000 E150FPXSSM LOOSES IGNITION ON START UP

    T&T is short for tilt and trim system the plug is triangular on a ETEC ... using the FDTI drivers with the USB cable or serial interface. did you read HELP FILES the other one booth strap is for brain surgery on the ECM .do not use!! did you follow instructions to register...
  9. C

    Evinrude 6hp gear shifter out of alignment

    any channce this part ended up loose allowing the shifter to get out of alignment
  10. C

    Parts Catalog for 1956 Johnson 5.5 HP CD-13

    fyi when you do the impeller ... looks difficult but really it isn't. carefull with the carbon seal under the Power head ...VERY VERY FRAGILE !!! $$$ try not to damage the base gasket under the PH... if you need to order one make certain year is correct because gasket patterns differs...
  11. C

    Parts Catalog for 1956 Johnson 5.5 HP CD-13

    if not here the folks at AOMCI may have it https://www.aomci.org/forums/forum/ask-a-member-d1/
  12. C

    1970 25hp Johnson lower paint question?

    http://nymarine.ca/colours.html
  13. C

    Evinrude family heirloom

    when you decide if it needs it.... the carb simply needs a good clean up with carb cleaner in all orifices followed by a strong blast of air. one critical issue these days is cheap Chineese carb gaskets which have been reported as shivrling away or....litterally melting to goo state so...
  14. C

    Evinrude family heirloom

    here is a great book btw to guide you to restoring your oldy. and your grand kids will be able to run great great granpa's motor. https://www.chapters.indigo.ca/en-ca/books/cheap-outboards-the-beginners-guide/9781891369629-item.html?msclkid=a457b4dbc11311ec91bb5eb11fa981c7 Evinrude and...
  15. C

    Evinrude family heirloom

    why not just fire it up after... you install a new impeller. it could work perfectly if stored properly (carb drained , cylinder oiled up gearcase emptied and refilled before storage. in any event check the GC oil for water contamination .. if none dump the oil and refill (cheap cost. )...
  16. C

    Loud ping / clinking when switch to neutral Evinrude E-tec 60hp

    strange... you should also post on the ETEC user board where E-TEC folks hang out incl. expert mechanics ( no offense to anyone) https://www.etecownersgroup.com/?forum=136482
  17. C

    225 ocean pro (won't start)

    You are here: Home / Cruising & Chartering / Outboard Won’t Start 101 Outboard Won’t Start 101 Published on November 27, 2017; last updated on September 19, 2021 by Carolyn Shearlock Pin it! So, your outboard won’t start. What are the likely causes? What should you check first? Second? Third...
  18. C

    225 ocean pro (won't start)

    no not a dump response ... if the fuel is fresh it is a non issue. ... just going by the color which seems..yellowish a bit
  19. C

    225 ocean pro (won't start)

    thanks for info diagram was specified to be an example only and a possible source of problem .. in latest pict (DINGBAT) fuse is shown to feed 12v to the trim switches. Yes I agree main 12v high current feed is directly connected to relays yet T&T control switches are fused . Hence...
  20. C

    Firing up remote control Johnson big twin 40 ( super Seahorse )

    time to clean the carb ....no fuel entering the crankcase... no fishing remove bottom "drain plug" blow in carb cleaner is a minimum . pictures shows a HS needle but yours is a simple non ajustable orifice.
Top