Search results

  1. C

    Power pack and coil AGAIN!!!

    This time engine will not crank, just turn over...???? can you elaborate
  2. C

    6HP Johnson Tune Up

    well carb looks old style with top idle drip chamber which may be gummed up . removal/inspection may be worth while since idling is poor see old design...built into your " modern carb" Seen recent comments on high octane which indicated it serves no big advantage High...
  3. C

    evinrude carbs

    carb and toilet bowls work the same way... the raising float stops the inflow of water...or fuel in a carb when either one does not work you have overflow :) take the carb apart , inspect & fix the mechanical issue stopping the inlet needle from doing it's job of shutting the inflow of...
  4. C

    Engine Does Not Crank - No Tilt/Trim

    Great news and thanks for you positive feedback. we all learn from it. Yours was a second identical case (bad fuse) in recent weeks keep that old selenoid in case the " modern" one does not give you 30 years of great service :-)
  5. C

    JW10 no spark problem?

    or..simply set at .020 at the highest point of the cam lobe
  6. C

    4 wire rectifier

    xx
  7. C

    JW10 no spark problem?

    did you burnish the surfaces a bit and clean them with carb cleaner wetted business card no real reason not to conduct at 0 ohms ... you did short your VOM probes and set the needle to 0 if analog. use the lowest ohms scale possible on your meter. try them out because the...
  8. C

    Have a j8renm. It had beem sitting for a few years.

    if it is just a water gasket... can you just cut one up from gasket material
  9. C

    Evinrude Recoil

    any possibility of installing a small bolt to replace the bent pin. you could just install it next to the existing pin ? even if it sticks out the top a bit you probably have a bit of room under the hood
  10. C

    Tilt/Trim problem

    see link to T&T issues search tons of info and possibilities for you to read. 3 cyl models 75-90...
  11. C

    Engine Does Not Crank - No Tilt/Trim

    You really do need to buy a VOM to check voltages and resistances :-) A volt meter would have told you if 12v passed either side of the fuse but fuses are cheap .
  12. C

    Tilt/Trim problem

    seals likely shot my 2005 did the same you can try adding oil but it will leak out. My dealer did the service but apparently if you are at ease with doing the work it is not all that hard to do. You need a tool to unscrew the top of the cyl and the seal kit the 2005 required...
  13. C

    johnson hd25 exact year

    check in at the aomci site for expert info on oldies... poche family site helps also ! http://pochefamily.org/outboard/
  14. C

    johnson hd25 exact year

    Re: Johnson SeaHorse HD-25 Questions from an old post searched it's a 1948 model. The range for that year was 614515-698874. I don't see any rebuild kits out there, but you can scrounge around for parts. Good haunts are: laingoutboards.com vintageoutboard.com nymarine.ca I think nymarine...
  15. C

    1979 Evinrude 2 hp 2902A torque specs

    not 2hp but close or try the chart http://www.ntractorclub.com/howtos/pdfs/Torque-Values-for-Common-Bolt-Sizes.pdf
  16. C

    1963 10hp Johnson QD-24 Flywheel rotating the mag plate

    see pic.
  17. C

    QD-22 - 1961 Johnson 10hp - idle help

    when you serviced the carb did you clean the complete low speed circuit incl removal& replacement of the top dime size plug to clean the 3 small drip holes. the idle circuit feeds gas to the top half of the carb by suction via a side channel which must be cleaned (use carb cleaner and...
  18. C

    Engine Does Not Crank - No Tilt/Trim

    https://forums.iboats.com/threads/no-power-to-start-motor-or-tilt-on-48-hp-johnson.745755/ see post#17... and others for fuse location
  19. C

    Engine Does Not Crank - No Tilt/Trim

    see similar case recently see text for fuse location https://forums.iboats.com/threads/no-power-to-start-motor-or-tilt-on-48-hp-johnson.745755/
  20. C

    Engine Does Not Crank - No Tilt/Trim

    where the main batt connects to the selenoid IN side follow the smaller wire (s) attached to the same post .. usually anyway
Top