Search results

  1. C

    1971 evinrude 9.5

    2x Ignition Coils For 580416 584477 Outboard OMC Johnson Evinrude 1.5-40HP | eBay slow mail but cheap
  2. C

    1971 evinrude 9.5

    doing a carb job is not complicated see good utubes ...it is good insurance dont forget an impeller and new gear oil (check for water intrusion) (596) 9.5 Hp Johnson Evinrude Outboard Carburetor Rebuild - 1of2 - YouTube when you reinstall the carb carfull with the cam follower/carb set up...
  3. C

    Need Kill switch Repair vs. Replacement 1985 6hp E6RCOB.

    these are nice and water proof with easy mounting (Pack of 2) 19mm Momentary Push Button Switch Waterproof Stainless Steel Metal Flat Top 12V 24V 36 DC 110V 250V AC 5A 1NO SPST Screw Terminal APIELE: Amazon.ca: Industrial & Scientific just fill the end of the throttle with goop rubber for...
  4. C

    1999 Evinrude 115 Ficht - cold run issue?

    reminds me of my 75 etec crashing to SAFE MODE with NO OIL code 38s on cold start ups (fixed with new oil pump and S/W update) most hard shut downs on todays EMM are related to - high engine temp (unlikely) - high emm temp (unlikely) - to many NO OIL alerts ( newer xd100 cold...
  5. C

    1969 6HP Impeller replacement

    fyi I just ordered 3 thermostats from EBAY for 10$ CND ..about $7 U$ a piece with free shipping. from seller VKI_GO my lower price bid was accepted :-) I offered 10$ CDN for 3 instead of $13.00 each don't forget the rim gaskets !!
  6. C

    Trying to start a 1967 33hp Evinrude no Generator

    Boatinfo - 1922-1964 Johnson Service Manual this book does not cover your model but being a good old magneto engine you will find tons of valueable info on carbs, magnetos etc... utube has lots of info on fixing /tuning magneto engines like yours testing coils points etc...
  7. C

    Gear oil leak 1985 9.9 Evinrude

    you are running in cold temps with sharp variations while running the engine then shutting it off possibly generating some condensation in the lower exhaust routing..and drain. could be just sludge- crud oil and gas exhaust mixing and draining down and out. it also seems to come out...
  8. C

    Cowl replacement or repair.

    I have use "BONDIC" to repair broken bolt tabs on the ETEC lower plastic housing then cover up the "welds" with pieces of fiverglass cloth inbedded with permatex PLASTIC WELD Bondic is an instant weld UV glue for plastics (works just like dental repair putties your dentist uses and...
  9. C

    Cowl replacement or repair.

    how bad is it ?? pictures ??
  10. C

    1976 55 HP Johnson

    well since the pump is new and presumed working it could still be clogged from that "old" tank . check filter under the pump cap and tank pick-up cost 0$
  11. C

    Obsolete fuel line question

    B.O.A.T. break out another thousand they say :-)
  12. C

    Starter rope replacement 1998 8hp Evinrude.

    I buy my starter cords at a tool rental place . With multiple power tools and negligent customers wearing down/breaking pull cords all the time they have good quality cord in all sizes for their tool maintenance shop and us "outboarders" . They sell me whatever I need at minimal...
  13. C

    1976 55 HP Johnson

    pumping the bulb is usually indicative of a weak or faulty fuel pump check for small air leak or try a new tank & hose from a buddy also..check all filters for obstruction, tank pick up etc.. especially the one under the cap on the fuel pump..
  14. C

    Obsolete fuel line question

    $60 for.. a few hoses doesn't seem to bad for peace of mind if this is the first hose swap on a 80'S engine (40 years of reliable service) I would not worry about the next swap :-)
  15. C

    Starter rope replacement 1998 8hp Evinrude.

    btw if the wear/break area is the same you can always slip on a 10-12 inch piece of heat shrink tubing over the pull cord . It should not impeed the operation while protecting the wear zone. :-)
  16. C

    Buying CDI rectifier ? Johnson 30 hp 1987

    looks like you found the solution to your problem.
  17. C

    Buying CDI rectifier ? Johnson 30 hp 1987

    what problems did this create sudddenly ?? if handy with a VOM you can probably test the 3 diodes . A 3 phase rectifiers is basically 3 diodes with outputs going to the RED lead Did you measure the voltage on the connected battery posts or are you seeing this on a depth sounder or...
  18. C

    Starter rope replacement 1998 8hp Evinrude.

    try to polish off any friction areas if any on the guide'S inner surfaces.... you can always buy a new guide maybe the fixed the "problem" what was the life span on the pull cord 23 years...??? if so, I would not declare this an issue to fix. make certain you reinstall a quality pull...
  19. C

    Upper Water Tube Grommet Replacement 6hp 1985.

    .......So unless I can find a 3rd Party to download Flashplayer from, this isn't going to work for me, correct? i guess so. :-(
  20. C

    Upper Water Tube Grommet Replacement 6hp 1985.

    the three small dots (using EDGE) are at the top right just below the X used for closing an open window window. clicking the ... will open up a long list of subjects and at the bottom you will finf a star wheel logo click the star wheel to access parameters in the parameter...
Top