Search results

  1. C

    6hp fisherman idle issue!!

    what did you do to "clean" the carb ? did you inspect and clear the top drip chamber and the very small orifice feeding the top half of the carb via the side fuel channel ? see carb issues on older carbs yours has no bowl but basic issues remain
  2. C

    Evinrude Big Twin 35 Restoration

    folks at the aomci ask a member can help out also on reviving your oldy Ask A Member | Antique Outboard Motor Club,Inc (aomci.org) you do not need to be a member to ask questions they can guide you to a parts list for your 1958 gem OMC outboard related articles (leeroysramblings.com)...
  3. C

    1999 Johnson 70hp not peeing

    if you pull the thermostat do you get water on top on the engine ? have you tried running the pump on its own to see if it pumps properly ? water tube grommets not crushed ? missing any parts on the old impeller ? tried a piece of heavy fishing line up the pee hole ?
  4. C

    Evinrude 15 1992 Tiller arm low speed

    great.... having no specific parts diagram for that given mdl #...... ...I am out
  5. C

    Evinrude 15 1992 Tiller arm low speed

    looks like a Belgium made model... see an old post from 2008 ... b-----belgium e-----evinrude 15----15 hp ba----ac lightning -rope start en----1992 m-----model run or suffix dec 04 2008 Model Be15baenm Serial No 08916066 According to this it is a year 1992. When I look at the parts...
  6. C

    Evinrude 15 1992 Tiller arm low speed

    on the parts diagram the knob connects to a small cable which rotates a gear at the bottom of a vertical shaft.. presumably if you find the gear and shaft in your model one would think it should do the job of adjusting the throttle... please post your engine model on the plate
  7. C

    Evinrude 15 1992 Tiller arm low speed

    the end part in the diagram should rotate it seems.... tried some wd40 ? on all the parts Steering Handle & Throttle Control Parts for 1992 Evinrude 15 hp it is hooked up to a THROTTLE CABLE ASSY. which rotates a cam called SHAFT, VERTICAL CONTROL
  8. C

    1971 evinrude 9.5

    CAUTION... always wear eye protection to protect eyes and any tinted eyeglasses . carb cleaner can dissolve any protective coatings on eyeglasses yes.. just unscrew the lower bolt then use the plastic straw against the HS jet inside and the carb clearner solution will blow out the...
  9. C

    1971 evinrude 9.5

    high speed jet is fixed behind the lower bolt (keep it clean !! the LS needle unscrews.. carefull not to loose parts for points the highest point of the cam can be used and set points at .020 or sense when the pistons reach TDC with a screwdriver in the sparkplug holes. BUt.... you...
  10. C

    1965 6HP Gearcase Not Sealing

    can you try to JB weld broken area ... drill & retap as for gearcase pitting you could probably resurface it with some JB weld KwikWeld Professional Size | J-B Weld after a good sanding job.... clean all greases and dust mix up some JB and smooth it over the pitted areas let...
  11. C

    1989 70 hp evinrude won't crank

    Great news :-) glad you got her fixed up and gave us the feedback . I had a similar issue on a MERC 50 years ago. .found a broken wire in the side fat connector, the result of years of bending .
  12. C

    1973 evinrude 135 starflite

    look at it this way $1000 for a potential boat anchor is pricy.. it will need some work (impeller carbs, ignition check,gear case etc,,, Being a possible low hour engine is great but 32 years is a lot of time for rusting due to humidity , bugs etc... try for $1000.. an able bodied...
  13. C

    1989 70 hp evinrude won't crank

    progress..I get 12 volts on that wire. I get 12 volt into solenoid an Checking other points (like primer solenoid ) today ok if you have 12 v one of the control posts of the selenoid then the other small post would need to be grounded to get the internal coil energized on some circuits...
  14. C

    1989 70 hp evinrude won't crank

    great .. getting more difficult to get diagrams with Adobe flash player now R.I.P. thanks for info. o.p. mentionned NO spark when jumpering the selenoid .. odd that it is not sparking and selenoid is not working. testing and tracing seems in order. "starter is good as...
  15. C

    1971 evinrude 9.5

    got a freebie myself MQ13 if correct all white missing a carb link and parts. when I flipped it upside down all the missing parts came out. :) with some sand ... and crud
  16. C

    1989 70 hp evinrude won't crank

    the fact that you have 2 symptoms (no sparks... no start) would indicate it would be a very bad lucky situation to have a bad selenoid. selenoids are simple devices with a single internal coil to magnetically close the starter circuit . the control wire should show 12v while in START...
  17. C

    1989 70 hp evinrude won't crank

    did you mean D ??? sinc A would be solid bat +12 and B the selenoid output to the starter when coil voltage is applied on C &....D
  18. C

    1971 evinrude 9.5

    dont want to hold up this thread...but on this subject of condensers 7.5V or 120AC (rectified I presume) would generate a test voltage much lower than 270DC in W.Mohat's test box. His test box would seem more sophisticated to test a shorted or "leaky" condensers.
  19. C

    1971 evinrude 9.5

    thanks for info on condensers i'll include a warm up on the next one's I test in the future.. just out of curiosity do you know what voltage level was used on the Merc -O-Tronic tester . The AOMCI w.mohat tester i built checks out at 270 DC oddly my problem is at start up so my...
  20. C

    1971 evinrude 9.5

    I envy a one pull cold start 9.5 :-) my beauty 9622a Evinrude is a bear to start and I have pretty well all I can do and I mean all ! After the bear wakes up with a shot of carb cleaner it will run smoothly all day long trolling. Now that I built me a capacitor test box I will go over...
Top