Search results

  1. Scott Danforth

    Just 3 Words

    stubbed my toe
  2. Scott Danforth

    Just 3 Words

    I gotta pee
  3. Scott Danforth

    1991 4.3 Volvo Penta DP-C tilt will not raise outdrive

    Look up parker oildyne 108 reservoir. They are about $20. Same onea that mercruiser sells. Can also hit up your local parker hydraulics store
  4. Scott Danforth

    1991 4.3 Volvo Penta DP-C tilt will not raise outdrive

    your drive is above the limit of the trim and you are getting into the Tilt range you are pulling up on the 2ndary switch to allow the drive to go up further, correct? trim is the thumb switch, the 2ndary switch is the one under the fingers the other posible issue, if you hear the pump and...
  5. Scott Danforth

    Mercruiser 4.3L pushes 2400# runabout only 36mph max

    Prop diameter has so little to do with the prop performance compared to the pitch. I would drop down to a 19P
  6. Scott Danforth

    Carbed Mercruiser 260 5.7L Missing Above 4000 RPMs

    you may also need the mercruiser fuel test fitting if you are only getting 9 volts, you still have the ballast wire in the system. follow the igniter II instructions. however, as I stated prior, I would rebuild the distributors vs spending money on new ones.
  7. Scott Danforth

    Advice on transom , stringers and floor rebuild

    in about a month and a half the resin supply will be back up. Lumber will be back down lower in about 3-4 months
  8. Scott Danforth

    Omc 5.7 engine replacement

    Lower **** cable has gone up to $850 lately
  9. Scott Danforth

    65 Larson Lapline

    First, welcome aboard You are looking for a needle in a haystack for the windshield. Bimini tops didnt exist in 1965. They came about 30 years later. So look in the iBoats store for aftermarket bimini tops
  10. Scott Danforth

    Omc 5.7 engine replacement

    Do it your way and damage the boat Follow the manual which is just a bit more indepth than post #2 and 5 and you avoid damage. Pay particular attention to the correct method if disconnecting the lower shift cable.
  11. Scott Danforth

    Omc 3.0l 1991 prop nut size

    i think they standardized on teh 3/4-16 of the Alpha.
  12. Scott Danforth

    Advice on transom , stringers and floor rebuild

    depends on your span. the floor in my boat is 1/2" balsa with a bit more than 1/8" fiberglass on both sides. however the widest span is 36" and there are 1/2 x 1-1/2" ribs every 2 feet. if you have a short span, 1/2" would be enough with 3 layers of 1708
  13. Scott Danforth

    Water Pump Question - Alpha 1 w/Closed Cooling

    wont need much flow on the engine stand.
  14. Scott Danforth

    Water Pump Question - Alpha 1 w/Closed Cooling

    the alpha 1 pump will work with some half systems, however not full systems. who's kit are you running?
  15. Scott Danforth

    Ports through hull on 1991 Sea Nymph?

    most of the plumbing is plastic fittings and pvc hose that are bolted to the livewells and deck prior to dropping the assembly into the boat. since the boat (and all the sub systems) are designed only to last about 15 years, the plastic fittings break, the hose crack, the plastic thru-hulls...
  16. Scott Danforth

    Newbie

    its right there in the picture, so it must be in your drive way. all the information you ever need is right there on the title. are you trying to find information on the boat with internet searches? remember, the internet only came about in the early 90's. so unless someone goes thru the...
  17. Scott Danforth

    Carbed Mercruiser 260 5.7L Missing Above 4000 RPMs

    use a fuel pressure gauge and check fuel pressure. that will tell you the health of your fuel pump is the carb inlet filter in good condition? is it clean? which pertronix kit? igniter - the one with the magnetic sleeve that sits on the cam lobe, igniter II - the one that reads the cam...
  18. Scott Danforth

    Omc 5.7 engine replacement

    Being a 1984, you have a stringer drive. Remove outdrive, remove boot, unbolt stringer mounts andbpull motor and intermediate housing as a unit
  19. Scott Danforth

    Do you know the OEM Prop size for a 05 Bayliner 265 with 5.0NA 220hp Carb engine.

    I would say 15x15P based on the performance of the same motor in my searay and that was 3600# and used a 15x19P
  20. Scott Danforth

    Why an increase in engine horsepower will hurt your ‘holeshot’, acceleration and midrange cruising.

    202 duration intake 214 duration exhaust 395" lift intake 404" lift exhaust 112 lobe separation. from this post https://forums.iboats.com/threads/venturing-into-performance-upgrades-for-an-aq271c.489465/post-3456952
Top