Search results

  1. kbh121956

    Help identifying a Tilt & Trim unit

    This is the Mercury style pump and motor, look for used. You can get the motor but not the pump. If you get a new motor, make sure that it comes with the shaft. DB Electric has the motor and it comes with three different shaft lengths. Inside the pump is some springs and balls. I recently helped...
  2. kbh121956

    1994 Force 120 HP Ser. # 0E089004

    Thanks topgun3690. I think both of us figured it out at the same time. I removed one wire at a time on the switchbox to read what was marked (under each wire the switchbox is marked). You are very correct, the black/yellow wire did indeed run to a single color black. That black wire runs over to...
  3. kbh121956

    1994 Force 120 HP Ser. # 0E089004

    This 120 really runs well, so well that the ignition switch doesn't turn it off. It uses Mercury's Thunderbolt ignition system. The CDI Electronics website states that the Black/Yellow wire is the kill circuit, if you ground it, it should shut down the engine. Problem is there is not a...
  4. kbh121956

    Wiring diagram?

    It uses Merc's Thunderbolt system. Exactly what topgun3690 sent in the diagram.
  5. kbh121956

    Wiring diagram?

    Thanks for the help. Do you happen to know what number 9 is?
  6. kbh121956

    Wiring diagram?

    I am working on 1994 Force 120 HP with the Mercury electronics. Installed a water pump kit, Went through the carbs. It is a strong engine. I tried finding a factory service manual and had no luck. The SELOC manual for it is pretty much worthless. When I start it up she runs awesome, turn the key...
  7. kbh121956

    WATER PUMP LINER

  8. kbh121956

    What is this?

    Can it be capped off? This outboard will be going on an older boat that uses the old style.
  9. kbh121956

    What is this?

    Thanks for the reply! I was thinking speedometer but wasn't sure.
  10. kbh121956

    What is this?

    This 1994 Force 120 HP Serial No. 0E089004 is new to me. I have it mounted to the stand. I started it up and the water pump impeller needs to be changed. My question for the group is, what is this hose? All my other Chrysler and Force OB's do not have it. This Force is newer, made by Mercury.
  11. kbh121956

    1994 Force 120 HP 0E089004

    Side control. It is also a 8 pin. I have not been around the later Force OB's so this is all new to me. Will any Mercury style work?
  12. kbh121956

    1994 Force 120 HP 0E089004

  13. kbh121956

    1994 Force 120 HP 0E089004

    Hello Group, I picked up this force. The controls are bad. It has the Mercury type ignition. Can anyone send me a link to a new control for it.
  14. kbh121956

    Part interchange

    Awesome, you guys answered my questions. Thanks again.
  15. kbh121956

    Part interchange

    Hello group, I own a 1963 Mercury 650 4 cylinder. I was wondering what parts will interchange from newer 60's early 70's 65HP 4 cylinders?
  16. kbh121956

    1963 650hp Tachometer hook up.

    Thanks for replying. I removed the tach. It doesn't have a model number on it. It does have a red, black, and a small gray shielded wire. and the light bulb wires. Shame as it is a set with the speedometer gauge. On the back of the unit all it states is "2 cycle outboard". MT 1 17 6. and the...
  17. kbh121956

    1963 650hp Tachometer hook up.

    Hello Group, I have a Mercury 650 Serial# 1543598. The outboard was bought with the boat in 1963, I am it's second owner. It has a "Aqua Meter" tachometer in the boat that has not been hooked up. It is only a 2 wire tach, a coax style wire (a center wire with the braided shielding wire, the...
  18. kbh121956

    Is it needed?

    Thank you to those that replied back. I will look into the HDPE. It also comes in black or white.
  19. kbh121956

    Is it needed?

    I was thinking of 1/2 white plastic. 1/2" aluminum would look very nice if I could find it.
  20. kbh121956

    Is it needed?

    On the outside of my 1971 StarCraft 18' SS is a triangular shaped piece of wood where the outboard mounts up. My question is, is it needed? I restored this boat a few years back and this plywood doesn't hold up well. The paint peels, looks terrible.
Top