Search results

  1. cc67

    Vintage Johnson dual line gas tank - fit Evinrude 5.5?

    There is a pump on the tank. You have to manually pump fuel to the carburetor.
  2. cc67

    1957 Evinrude 5.5

    Is it in gear?
  3. cc67

    1957 Evinrude 5.5

    Push that lever down and to the left. You should then be able to tilt the motor.
  4. cc67

    Evinrude Fastwin values?

    After you replace the coils and sparkplug wires, rebuild the carb and reseal the lower unit, you'll have a couple hundred or so in it so I wouldn't give more than that for one to begin with.
  5. cc67

    74 9.9 upper motor mount

    Good information, Thanks
  6. cc67

    1955 25hp Johnson RDE-17 compression

    Some eye candy. One I restored a few years ago.
  7. cc67

    74 9.9 upper motor mount

    I probably already know the answer, do I have to remove the power head to replace the rubber upper motor mounts? I don't see any way around it.
  8. cc67

    1958 QD-19

    The starter housing (376665) on my 58 QD is broke where the starter pulley bolts to it. Is the metal some sort of pot metal? Probably can't be welded. This little motor runs great and looks like a survivor to boot.
  9. cc67

    1955 Johnson RD17E

    Just finished this one last week. Almost too much for the 14' Alumacraft. [/IMG] [/IMG] [/IMG]
  10. cc67

    1956 15 hp Johnson

    Been working on this one for about a year. Turned out pretty good. http://i291.photobucket.com/albums/ll289/kink1955/Old%20Outboards/5615hp007.jpg http://i291.photobucket.com/albums/ll289/kink1955/Old%20Outboards/5615hp005.jpg...
  11. cc67

    Fuel pump kit

    I'm trying to find a fuel pump rebuild kit for a 67 Johnson 20 hp. Marine store doesn't have anything that old as far as I can see. Want to convert an older motor to a newer pump.
  12. cc67

    RDE cylinder cut out

    Got my 55 Johnson 25 running yesterday and was wondering what set of events would cause the cylinder cutout to kick in? I might have wound her a little tight in neutral and it started sputtering like on one cylinder.Had to choke it to shut it off. It would start back up easily though. I want to...
  13. cc67

    Casting number

    Anyone have a block casting number for a 56 FD-10? Or a copy of a parts manual.
  14. cc67

    Homemade flusher

    Got to messin around the shop this morning so I thought I'd try to make an engine flusher cause the muffs don't work so good on older outboards. Had a lower off a 67 20hp Johnson that was junk so I scabbed the upper water intake plate off it. I drilled a hole through the plate and threaded a...
  15. cc67

    AOMCI site

    Anyone know what's up? It's been down for several days.
  16. cc67

    Sea King 3HP

    I have a Sea King sold by Monkey Ward. #GG8962A. I have no idea what year it is. It needs a new plug (anyone know what #) and I replaced the cracked coil and plug wire. It is in surprisingly good condition so any Info would be greatly appreciated. I'll post some pictures when I get it cleaned up.
  17. cc67

    Qd-19

    Anyone have the Sierra part number for a float and the carb kit for a 58 10 hp Johnson? Thanks
  18. cc67

    Forum changes

    I noticed some changes to the forum. When did this happen?
  19. cc67

    57 Fd 11

    Went out this morning with the intentions of buying a boat but came home with this little Jewell instead. Got a tank and an extra female gas line connector. I haven't had time to give it a spit and polish but the inside is as clean as a pin.
  20. cc67

    Used impeller

    There is a guy on e-bay right now trying to sell this impeller. Advertised as "in good working condition". I think someone should jump right on it. :D
Top