Search results

  1. A

    1987 Glasstream ProBass 1550 'restoration'

    Very cool boat, thanks for the pics !! Being an older glass boat, take a little time to check the transom and stringers for wood rot. Being stored inside, you might be luckey and they are still solid. But...wouldn't want any dissasters to effect you and your son's enjoyment..
  2. A

    Cleaning fishing rods

    Good to know...thanks !!
  3. A

    2000 70 hp Low rpm under load

    Definetly replace all fuel hoses !! That and install a new impellor.
  4. A

    1984 yamaha 150 2stroke

    Double check all connections for rust or corrosion. On older motors this is common, all connections should be nice and shinney clean. Can't say that is your issue, but intermitant problems are often caused by poor connections. Good luck!!
  5. A

    2000 70 hp Low rpm under load

    Thanks for posting these examples, many folks don't realize how much crap can get into a carb, or build up inside from sitting. Draining is best for storage, but good storage products can slow down or eliminate these issues.
  6. A

    How to register a boat without a title or original bill of sale.

    Your safest bet is to go directly to the local office that handles this, actually go to two different ones and see if you get the same instructions !! Situations like these are often up for interpretation, that is why you should get two opinions from two different offices.
  7. A

    2007 mercruiser 3.0 Rust by the looks of it on side of block cover

    My 1983 3.0 was totally painted from the factory, just looking at his side covers, they appear to have streaks from a leak running down them.
  8. A

    Cleaning fishing rods

    Thanks, I will certainly test it first !!
  9. A

    Cleaning fishing rods

    I don't have any salt water near me, (great lakes area) and not concerned about keeping them for 30 years. They are just getting ugly and tend to be slippery when the stuck on scales get wet. From what I read here, I am looking for my scruffy pad, a pad that removes bugs but doesn't scratch...
  10. A

    2007 mercruiser 3.0 Rust by the looks of it on side of block cover

    Any leaks in that area when it is running? Grab a flashlight and look carefully for any signs of water leaks. My 1983 3.0 doesn't have any rust like that.....salt water use ??
  11. A

    VHF antenna

    If your concerned, fabricate a removable support to use while trailering. Look at "RAM" mounts as a thought to get you started.
  12. A

    76 Starcraft Holiday resto

    Your cracked ribs are a classic example of running aluminum hulls in rough water at high speed thus pounding the hull until the ribs crack. Been an aluminum hull boat fan for over 60 years. On big lakes like Erie, it is not uncommon where folks run hard in big waves. After welding you wil still...
  13. A

    Cleaning fishing rods

    You must have one big dishwasher to get a 7' rod in there, or mabey you were refering to the person that does the dishes as the " dishwasher" ....my wife is dissabled so I am the sole dishwasher, so I will be cleaning my own rods, so in some respects, being the dishwasher in our house, the...
  14. A

    1970 20hp johnson Ran Hot

    Of course, anything can be rebuilt with enough time and money. But...is an old motor worth all that will be needed ?? Only you can answer that. Most folks are not interested in major overhauls, just routine maintenence, but even that part often gets overlooked as long as it runs.
  15. A

    Transom Repair, Caribbean Jaguar.

    If the transom is bad, the stringers will be worse ! Gonna need to remove floor and get down into the skeleton of the structure. You have your work cutout, time, work and money, it will take a lot of each !! Be sure you have good safety gear, breathing fiberglass dust and fumes can be deadly..
  16. A

    Mr & Mrs Claus go camping

    What snow belt, here in Ohio we haven't had enough snow to even sweep the sidewalk in years !! I gues that if I want snow, I need to sell my snoblower first !!
  17. A

    1970 20hp johnson Ran Hot

    "It bogged down on me a couple times trying to get back to the dock" is a mistake ! This is what paddles and oars are for. If hot enough to stall probably scored cylinder walls. I would not be dependent on that motor any longer, your call....
  18. A

    First boat - 60hp Bigfoot - trim won't stay up during above no wake operation - what is normal?

    You sure ut has power trim and not just tilt ? Many outboards just had power tilt only and would not hold under pressure of speed. Otherwise...you have a problem ....
  19. A

    Yamaha 2022 outboard rigging guide

    Should have the factory service manual as well on their site. Try calling Yamaha direct. I generally buy older motors used, but on ocassion have bought a couple new outboards. Always ordered manuals for the new motors directly thru the dealer or ordered from the factory. On my older motor...
  20. A

    Cleaning fishing rods

    I do a lot of yellow perch fishing and we use emerald shinner minnows as bait and there scales come off and stick to anything and everything. Once dried they are very tough to remove, to the point of having to scrape them off my rods. Some of the rods have cork handles, so anyone have a good...
Top