Search results

  1. alldodge

    2000 Sea Ray 5.7EFI alpha 1 gen2

    I'll let someone else answer that one
  2. alldodge

    2000 Sea Ray 5.7EFI alpha 1 gen2

    The permalube is the same on both sides and should see a white dot The old style with cutouts , the center sticks out further if put in backwards Again main reason is to find out who did the work and is it fully seated
  3. alldodge

    2002 volvo penta 5.0gi TBI only starts with throttle

    Did you change all of these items? What is the fuel pressure?
  4. alldodge

    2000 Sea Ray 5.7EFI alpha 1 gen2

    Was the gimbal ring put in correctly, and is it seated fully? Look at the gimbal and if you can see cutout on the outer edge of the race then it was installed backwards If the same mechanic that installed the gimbal is also telling you its good, then suggest ask another or check your self
  5. alldodge

    Need help with sterndrive parts

    Just guessing but the shutters are item 6 and have to remove the elbow to get at it. Can also look down to see if other items are there https://www.mercruiserparts.com/bam/subassembly/30906/11669/190
  6. alldodge

    60A Circuit Breaker pops on engine shut off

    Breaker might be the issue and needs replaced Get any 60 amp fuse you can find and replace the breaker with the fuse. If it blows there is a real issue This is for 2 fuses but should be able to find just one https://www.amazon.com/Blue-Sea-5253-MIDI-Fuse/dp/B00I0A0U9I
  7. alldodge

    max size for video?

    No vid can be attached that I'm aware of, they all get posted to another site like youtube or other and linked here
  8. alldodge

    Water in Bilge? Where can it come from.......

    Need to think about water pressure a bit more for a hose and in the water If the top of the gimbal ring sits at or under the water line then can also be the steering pin
  9. alldodge

    Need help with sterndrive parts

    Howdy Your file size is huge, use reduced resolution for pics if you can The metal pieces are the exhaust flappers. What motor are you working on and serial numbers are best?
  10. alldodge

    Water in Bilge? Where can it come from.......

    Only way to find is to look, and you already know where it can come from. Only other place is the exhaust pipe might have a pin hole or leak Dry it out, put in the water and stand on your head (so to speak) until you can see where its coming from Do understand not working on old boats. Guy...
  11. alldodge

    New winch

    That'el geterdunn
  12. alldodge

    Prop sizing on 2008 Glastron DS-205 with the 5.0GL engine

    It ran good before winterizing and now it doesn't Need to do a compression test.
  13. alldodge

    3.0L hard starting when warm

    You should have 12V on one lead of the TKS module full time, doesn't matter if the key is ON or OFF. It comes from a 20 amp fuse which is connected to the red/purple wire coming from the 50 amp breaker
  14. alldodge

    3.0L hard starting when warm

    Something isn't right. TKS is working when motor is first started. This says that the oil pressure switch works. Once warm temp switch is not applying a ground. The ground wire is not grounded, the wire going to ground side of TKS is broken or there is another bad connection. Check continuity...
  15. alldodge

    7.4L Overheating

    Power steering cooler is before oil
  16. alldodge

    Fuel Delivery/starvation Help troubleshooting

    Fuel supply can weaken over time but will not just come back like there was no issue
  17. alldodge

    7.4L Overheating

    Pump hose is on the right side facing motor the one in front
  18. alldodge

    6.2L 300HP to 350HP

    The differences are Virgin bore 6.2 is actually 377 cubic inch, 320 HP at the flywheel and 300 HP at the prop Reman bored .030 over is 383 cubic inch, 350 HP flywheel and 320 or so at the prop Edit: The above is prior to ECT or catalyst motors Here is the skinny with CAT motors...
  19. alldodge

    Throttle lever afjustment

    Unsure with VP, but most have a friction screw at the bottom.
  20. alldodge

    Prop Shaft Spins But Propeller Does Not

    Reading your first thread I would think about disassembly of the lower. There is something wrong it the shift area.
Top