Search results

  1. Faztbullet

    Who has installed Helicoils ?

    How did you make lower portion expand and lock in place?
  2. Faztbullet

    Need torque for prop nut

    All depends on if stock prop or using plastic hub..can range from 55ftlbs to 100ftlbs
  3. Faztbullet

    Motor opinion

    As you posted, less crankcase volume increase's crankcase pressure. Simply this speeds up the cylinder filling process but it will not add much to compression overall due to port timing as a lot blows out exhaust. Built several I6"s that would give a V-6 a run for its money. The only thing that...
  4. Faztbullet

    Motor opinion

    Not quite... https://www.screamandfly.com/showthread.php?19445-Crankcase-compression-for-experts
  5. Faztbullet

    Motor opinion

    This is why you should use the factory tester as it has no rubber hose to expand and reduce reading.
  6. Faztbullet

    Sticky timing base '96 Evinrude 200TXEDR

    Make sure you use locknut and not wing nuts on battery connections.
  7. Faztbullet

    Motor opinion

  8. Faztbullet

    Who has installed Helicoils ?

    Wont make any difference if you use a lil or a lot or where its applied. As it is inserted it will coat nearly 360° of the threads as its turned. Then when salt water weeps by the dissimilar metals will corrode themselves in place.
  9. Faztbullet

    Motor opinion

    Before you do anything make sure you clean/drain VST and check that fuel pump runs. Replace all filters on engine and I would send the injectors off to be cleaned and balanced. Seafoam will not clean injectors as they have filter in them. Remove and send to Brucato
  10. Faztbullet

    Looking in installing a regulator rectifier

    Could be a 1975 with 110hp cowl......need to post model number as requested as everything else is guessing. You could have a round one if old motor or water cooled if new motor.
  11. Faztbullet

    Sticky timing base '96 Evinrude 200TXEDR

    And a bad rect/reg is what melts the stator...
  12. Faztbullet

    Motor opinion

    Has it been sitting?
  13. Faztbullet

    Who has installed Helicoils ?

    I would take a sharp punch and peen it in place once inserted...
  14. Faztbullet

    Early 80’s merc 2.0 150 V6 brown band clamshell black max ratio

    Mounting bolt patterns have not changed on V-6 engines only gear/ratios/shifting. Only different pattern is a Inline gearcase and you remove the front stud to use on a V6.
  15. Faztbullet

    Help with troubleshooting electrics on 1975 Johnson 115

    Your manual is incorrect as you should only get 150v on the brn-brn/yel stator wires not the trigger wires
  16. Faztbullet

    Evinrude 115Hp V4 Project Rebuild / Repowering a Fourwinns Fling Turbo jet boat

    Plug the fitting on exhaust cover and: (A) drill and tap heads for crossover plumbing (B) Swap heads off old engine.
  17. Faztbullet

    #2 / #5 Cylinders Not Firing

    Check oil tank in boat not on engine..
  18. Faztbullet

    #2 / #5 Cylinders Not Firing

    3 bars,lamps or arrows flashing means the remote tank(on engine) has sufficient oil but the engine oil tank is low. either a malfunction or needs filling. Motor goes into limp mode reducing RPM
  19. Faztbullet

    2006 175 Optimax been sitting 8+ years

    If you applied power and they didnt run they are bad, Only replace with a OEM pump ...crap off Amazon does not work or work long. Might as well start trying to find a tracker diaphragm also as most likely degraded
  20. Faztbullet

    Mercury 15hp No Compression

    Check flywheel key
Top