Search results

  1. alldodge

    2007 Tahoe Q6 merc 5.0 305 MPI motor won't start after running it

    The rules out the fuel pump, that is when it won't start. All this info we need when it won't start. You have the HVS distributer and many have trouble with the cap but don't see that as the issue now. When you crank over the motor does the tachometer move up around 200 rpm or more? The...
  2. alldodge

    SOS... Guardian issue

    I do believe your pressure should be above 32 psi and should be in the 43 range. Cannot say with 100 percent certainty because I don't have a manual for your motor, only 31 which is for 2001 and a bit higher. Just for stinkers and giggles, go to the shift plate and find the gear switch. This...
  3. alldodge

    Engine running rough

    To power an electric pump it needs to have an oil pressure switch inline so if the motor looses oil pressure it will turn OFF the pump. You also need a bypss wire so when the motor is being started the pump gets power to supply fuel to the carb. Something like this A factory install is like...
  4. alldodge

    Sea water pump

    Have to disagree on this one
  5. alldodge

    7.4 mpi fuel issues?

    Using a 45 gallon tub is not the best way to run the motor, even if it covers the intake holes. Manual shows 43 psi while running, dropping down to 38 isn't bad but would like to see it a tad higher. With it idling remove the vacuum line going to the regulator and the pressure should increase...
  6. alldodge

    2007 Mercruiser 4.3 wiring harness plug

    Here you go, A - 12V B - Ground C - Wake (ignition ON) N - Crank (Start) They also make a 10 to 14 pin connector so you can do it the old way :)
  7. alldodge

    Mercruiser MPI fault 54 and 56

    The seawater pump low is code 23 The sensor is located on the power steering cooler and in most cases its mounted across the top of the rear of the motor. I have the drawing for the sensor and it looks like 24 MM but not sure because its fuzzy. This is what I have for the different ones in the...
  8. alldodge

    Cracked Bravo 3 Gimbal Housing

    Howdy Have not seen one like that cracked. Transom bolts are torqued to 23 FT LB, so over torqueing will cause some issues. Other possibilities can be from having a soft transom. In any case its my opinion that your not going to fix it, it needs replaced. And you can upload pics after...
  9. alldodge

    4.3 GL won't run over 2000 rpms under load.

    Yes, or even harbor freight, just google "vacuum fuel pump gauge" it will show several. The issue is getting the fittings to fit the pump to carb with a Tee. You could order one of these which fits between the fuel line and carb. Might have one at AZ
  10. alldodge

    New motor installed and won't start

    Not a VP guy but do know your motor is not timed using a timing light. You have the HVS distributor and the motor is brought around to TDC on number one. Then the distributor is installed as in the pic below. There is no further adjustment unless its not running very well
  11. alldodge

    Volvo Penta MD2010 InstrumentPanel with Start button, electrical unit problem?

    My thought is this is something inside the alarm module. Your alarm module is part number 873737 Have been searching for the wiring of it and have come up with some older ones but not this one. In most cases a slight change is made and then another part number is used. The first one below is...
  12. alldodge

    Thunderbolt V timing

    The TBV has to be put in base timing mode to set. If you have a MSD box, I don't know. To put in base timing for TBV you ground the Purple/White wire and the set timing
  13. alldodge

    Alarm tan/blue tracer wire

    The wire is hot when the key is ON, but should not be when the key is OFF. Power comes from the purple wire going to the alarm. The alarm ground side is the Tan/Blue and goes to lube, temp and oil.
  14. alldodge

    Engine coupler swap out

    I would suggest not using the 92 one either because it is also worn. Note the points on the teeth, all are worn
  15. alldodge

    99 Rinker mercruiser 5.0 stalled no start

    With only 11V you have a bad connection or a weak battery Coil check
  16. alldodge

    99 Rinker mercruiser 5.0 stalled no start

    Most the time its never the coil. Run thru the troubleshooting below and it should lead you to the issue
  17. alldodge

    4.3 Mercruiser TKS all of a sudden stopped planing and maxes out at 2500 RPMs in gear

    Will need a vacuum fuel pump gauge. Can be found at most any auto parts store https://www.amazon.com/Actron-CP7803-Vacuum-Pressure-Tester/dp/B0006V2BS2 Then you need to get it connected between the fuel pump and the carb. This requires a fitting to be placed in line so the carb can be...
  18. alldodge

    Mercruiser 5.7 exhaust bellow blowing

    I think your right, it does look dented in, and also the manual shows (Sort of) to place the screw on the starboard side While this should have no effect, but the hydraulic ram comes with a spacer inside to reduce the amount of trim in by 1 1/2 degrees. It should not have been removed, but...
  19. alldodge

    Video of binding steering - what's happening?

    Howdy It would normally get tighter as the wheel goes further off from center. The reason is the rubber bellows are getting tighter, and thereby there would be more force on the steering. Is it hard to steer with the motor running? If so look to see if the slots on the steering ram are...
  20. alldodge

    Mercruiser 5.7 exhaust bellow blowing

    That is real strange The item kind of looks like it would come from the bell housing side instead of the transom. I know your right but just to make sure we are on the same item. I would remove the transom assembly and then put a straight edge on the boat transom. It has to be in a bind...
Top