Search results

  1. Scott06

    1997 7.4 mercruiser mpi blue water inboard

    Would do a leakdown test. Could just be valve related and a valve job could fix it, but loss of oil pressure if accurate , also indicates bearing wear. michigan motorz offers remans if you don’t have a local machinist
  2. Scott06

    Aluminum DuoProps?

    @Scott Danforth probably knows the cross reference
  3. Scott06

    Freshwater Dry Joint Manifold

    Normally yes fresh water they will last the boats life if properly winterized. I would buy elbow and or riser gaskets and inspect what the passages look like. You can take them off and test with acetone If you like. when you summarize it and use it , open the drain plugs and probe with wire...
  4. Scott06

    2003 Chris Craft Launch 25 - VolvoPenta engine replacement - need engine advice

    For $13 k in parts would think that is an OEM long block with multi year warranty.
  5. Scott06

    Manifolds (Trying to figure out what I am looking at)

    It can be deflating but look at it this way - If they correctly magnafluxed or pressure tested the cooling jackets on block and heads before rebuild it would have to be a gasket or assembly issue. Also you have caught it early enough that it wont damage any of the machine work you have done...
  6. Scott06

    early vs late Cobra bellows.

    @Lou C is the Cobra SME on here
  7. Scott06

    1990 MasterCraft 190 TriStar hull repair

    That is the bottom of the V on the bow? looks like from beaching or trailer damage. Would be concerned that the stringers are roached too.
  8. Scott06

    2003 Chris Craft Launch 25 - VolvoPenta engine replacement - need engine advice

    I assume remote oil filter line or oil cooler line blew? Obviously using a Volvo engine will cost more but probably comes with better warranty. Will they install a new GM base engine ? it is litterally the same long block/base engine Merc and VP build into their engines for about $2k less...
  9. Scott06

    2003 Chris Craft Launch 25 - VolvoPenta engine replacement - need engine advice

    I'd be interested to see where the quotes come in. I think $20k soup to nuts would be light if you want to upgrade engine as part of a complete repower, incl transom and drive. If rest of boat is in excellent condition may make sense, but off the cuff I think you would be nipping $30k. For...
  10. Scott06

    Boat Trailer Bunk Carpet

    Yes I would prefer to leave the bottom open but have had trailers factory equipped both open at bottom and completely wrapped. My current Magic Tilt has open bottoms on the cypress bunks - issue is I have had carpenter bees drilling holes in the bunks... just something to keep in mind. I think...
  11. Scott06

    Salvage auction boat - can this be repaired?

    I would inspect it and make sure it had not sunk and engines were not under water, regardless of what the "carfax" says. One way to look at is what is blue book on the boat in no damaged condition. Obviously to get totaled the repair was more than blue book, so unless you do the work yourself...
  12. Scott06

    2003 Chris Craft Launch 25 - VolvoPenta engine replacement - need engine advice

    Were you happy with the power level it had when it was working? I assume you are looking for a complete bobtail to mate up to your existing drive ? Or are you looking for pulleys to prop complete repower? Looking for carbed or injected? Seems like you budget is bigger than typically seen here...
  13. Scott06

    rebuild 1989 bluefin 17 ft

    Yeah it does look like since it’s down in that recess someone has a sense of humor… work it back with two flat heads . If you can get one leg of it out of the groove even if you bend or break the clip. clips are cheap from McMaster carr or fastenal like place, so bend it etc to get it out of...
  14. Scott06

    Mercarb 2BBL vacuum hose?

    Yes makes sense. So put a nipple where the pipe plug is and put the Tyson tube up from mechanical fuel pump. interestingly while new build engines (except 3.0) used electric pumps from mid 90s on, the merc reman 357 alpha/ bravo engines they use a simple mechanical pump , assume they machine...
  15. Scott06

    Alpha won’t trim underway

    It would seem that the thrust of the prop is over coming the ability of the cylinder to hold? I would try to disconnect the cylinders and see if you can push them in while the trim is off. I had one of my cylinders bleed down like this , couldn't even hold the drive up when I was put drive back...
  16. Scott06

    Mercarb 2BBL vacuum hose?

    Is this a pipe plug (circled) in your photo? that I believe is where I had one on my Mercarb. Mine had a 90 degree elbow threaded on one end and hose nipple on other. like this fitting in amazon link -...
  17. Scott06

    rebuild 1989 bluefin 17 ft

    Are you able to get the big E clip off it
  18. Scott06

    Mercruiser 305 V-8 Temp issues

    thank @Bondo ... you didn't think I thought this stuff up on my own...
  19. Scott06

    Mercruiser 305 V-8 Temp issues

    There is no shifting in the upper only the lower. It is just a right angle gear reduction. When you shift into forward to reassemble put the prop on and use a bungee to hold it CCW. It seems counter intuitive because it is a RH prop- with pressure on it CCW it acts like the load water puts on...
  20. Scott06

    Mercruiser 305 V-8 Temp issues

    You found your not smoking but melted gun. If you take your time and go back in with OEM parts you will have no issues. Would also check the condition of your exhaust flappers as they are likely melted too. Obviously some one let it run without water at some point or maybe water tube wasn't...
Top