Search results

  1. nola mike

    87’ invader mercruiser help me ! 👸

    What's wrong with the current motor? I would *highly* recommend against this swap. It is not easy and takes a decent amount of know how to accomplish. Whatever is wrong with your current setup, it would almost certainly be a better idea to fix what you have. Besides, you have a pretty rare beast...
  2. nola mike

    Boat won’t plain starts too then just spins like slipping clutch

    Or stripped outdrive gears, broken driveshaft in the drive, or spun coupler. Which aren't cheap.
  3. nola mike

    Wiring help/Electronic gauge

    Anybody have any thoughts?
  4. nola mike

    No spark plug spark... 170 MC , 1985 Sea Ray

    Again, the cranking 12v to the coil on your engine comes from the pur/yell wire off the slave solenoid.
  5. nola mike

    Ignition switch failing?

    Huh, you mean like this? Was tracking down a voltage drop this weekend. Still got 0.25v across the switch, but this cost me almost 1v with no load
  6. nola mike

    Dripping engine block fitting

    It's just a standard npt pipe fitting, but I don't remember the size. ¼?
  7. nola mike

    1994 5.7L Weber carb

    Yup, I jumped to fuel without reading closely and noticing the misfire
  8. nola mike

    New to forum

    The space between is dry. Also that lower seal goes in the opposite way you'd expect, lip faces up. It should stop a leak from that upper seal if the drive shaft is installed.
  9. nola mike

    Cracked block - now looking to replace motor

    Your outdrive will work. Are all the accessories coming with the new motor?
  10. nola mike

    Dripping engine block fitting

    It'll drain a couple of gallons. Of course we have no idea what engine you have... Also, what's the rest of that rust from?
  11. nola mike

    Motor Knock

    Yeah, I'd be concerned about the crank, maybe bearings if it dropped that hard. I'd at least demand an extended engine warranty for a year or 2
  12. nola mike

    1976 Mercruiser 233 (Ford 351w) carburetor issue

    Correct. There are linkage adjustments but I don't know them off hand. Do you have a rebuild manual?
  13. nola mike

    online service manuals

    You can probably use old software and set your computers date back, but I haven't tried it
  14. nola mike

    1994 5.7L Weber carb

    Again, float level and drop are part of the adjustment. If you're running that rich it probably isn't the idle adjustment unless that's where you do most of your boating
  15. nola mike

    1994 5.7L Weber carb

    How did you adjust the carb? At the very minimum you need to check your float levels and make sure your needle valve is closing. But a rebuild is probably in order. Also need to check your fuel pressure.
  16. nola mike

    Possibly seized motor?

    I'd rather strip out an alternator pulley bolt than my crankshaft. There's a tool that bolts to the balancer you can use. Alternatively I've replaced the balancer pulley bolts with longer bolts and then used a pry bar to turn the balancer.
  17. nola mike

    Cracked block - now looking to replace motor

    Fwiw, the newer motors may have composite head gaskets as well... The '01 that I pulled had composite hg and brass core plugs.
  18. nola mike

    Cracked block - now looking to replace motor

    The core plugs on the new motor are likely already brass. Check before pulling them out. Also, is your old motor v belt or serpentine?
  19. nola mike

    Mercruiser 4.3L Just clicks once when trying to start! Help!!

    Battery isn't low (12.7v). You're getting a bit of a drop when cranking, but 11.8 should be enough to get it to turn over. Have you made sure that the engine turns over by hand? Have you tried jumping the terminals at the starter? There's a good troubleshooting section in the stickies...
  20. nola mike

    1986 Alpha One has leaked oil since service....

    Ooooh, extra points for using your boat motor to pull the vacuum!
Top