Search results

  1. C

    Old 1973 sportwin Evinrude

    How to Rebuild Ignition Magneto Disassemble Assemble Clean Test 1968 9.5 HP Johnson MQ-14D - Bing video
  2. C

    Old 1973 sportwin Evinrude

    actually there is an excellent utube in 2 parts on the 9.5 carbs... the rest is electricals (coils condensers points timing and plug wires) scan utubes there are good ones on rebuilding the ignition which is not that complicated. timing with a vom is also easy see video and you won't...
  3. C

    Old 1973 sportwin Evinrude

    it is called a bucket see pic of my "stuck" 9.5hp... $50 CDN :-) took me a week to unstuck it... has been running great for a few years now... just hard to start it is addicted to morning shot of carb cleaner ...
  4. C

    Old 1973 sportwin Evinrude

    expect compression from the mid 60'S to mid 70s higher would be better but work fine at 65-70 psi
  5. C

    Old 1973 sportwin Evinrude

    change impelller change gear oil look for water ... if water may need a GTC reseal test for strong spark 73 coils may be still good points may or likely need clean or replacement as well as condensers a good carb clean up won't hurt but it may function without one depending...
  6. C

    Johnson 9.5 carb

    see doc on 9.5hp aka turtle
  7. C

    Johnson 9.5 carb

    flywheel is now unballanced.....not good :-(
  8. C

    Johnson 9.5 carb

    vents are meant to let air in or out as the fuel level rises and fall inside the carb bowl the float should stop excessive fuel reaching the vent hence, as indicated, the float/inlet needle set up is not set properly carb and toilet bowl floats work the same way :) they rise...
  9. C

    Sync cam throttle on 71 Johnson 25hp

    run a good decarb product... not a big expense for a trial to much turbulence could cause cavitation
  10. C

    How to disconnect plastic linkage (1998 4HP)?

    don't realy know you can use a less harsh solvent like fuel oil kerosene you can tape up the plastic part on the shaft if worried fresh gasoline could surely do to clean the carb and that carb lives with gasoline all the time so i doubt it would be affected . air blow all passages...
  11. C

    How to disconnect plastic linkage (1998 4HP)?

    sorry .. I would not venture enough to give you a suggestion I think you can clean that carb without a full soak the upper LS needle can come out and if you want to do a full clean-up you will need to pull the top plug on the LS drip chamber see pic of an older FD carb much like...
  12. C

    How to disconnect plastic linkage (1998 4HP)?

    if you gently skweeze the splip part with pliers it should allow you to pull out both the link and plastic insert
  13. C

    Sync cam throttle on 71 Johnson 25hp

    deleted
  14. C

    1060 Evinrude fisherman 5.5hp

    puffitu... you really need a book to chase all these issues 60 posts on a 5.5hp must be a record :-) join up AOMCI and get yourself a free copy of the johnson maintenance manual downloaded form Garry Spencer's drop box. it is free to members it is a 691 page book covering oldies from...
  15. C

    Sync cam throttle on 71 Johnson 25hp

    how did you clean te HS jet behind the bottom bolt on the carb did you run a small mono or very small gauge wire to dig out any built up crud you should see light clearly if you look into the HS jet cutting suddenly at WOT may be a fuel restriction issue...if not electrical the low...
  16. C

    1060 Evinrude fisherman 5.5hp

    see pics & description fyi sorry bad file name .... shock absorber ! they need to be a very very specific length ... if broken some just weld them to the proper size then install a shear pin instead of a drive pin on the prop shaft. to remove the 6 GC screws I use a 1/4...
  17. C

    Ignition Shorting?

    I still can’t find the solenoid... flow the fat red wire on the starter !! there is only 1 (just follow the red brick road) Glad you found the stick buton ! you are on your way to become a carb expert :) if you are overly concerned you can try a half bottle of engine clear in a fresh...
  18. C

    Ignition Shorting?

    Wiring and 12 volts confusing... Not really... learning is a slow process which grandma explained very well when I was a kid. the human brain is like bottleneck. If you try to fill the bottle to fast you spill most of the liquid . Yet as time goes by the underlying objective is...
  19. C

    Ignition Shorting?

    just follow the fat red wire on the starter.... back to the selenoid OUTPUT POST ... the other fat post (INPUT) has a fat 12v from the batt. and smaller 12 v wires from the rectifier (the one with 2 yellows) and the other smaller bolted wire is the CONTROL wire from the start...
  20. C

    1060 Evinrude fisherman 5.5hp

    those are great motors ! just it feed it oil...and gas thanks for feedback
Top