Search results

  1. Scott06

    Volvo Penta 3.0 GLP-D Choke/Starting Issue?

    You have to pump the throttle to set the choke , as mentioned pull flame arrestor off and see what choke is doing during start up
  2. Scott06

    Ford 302

    Yeah i did the same when i repowered six years ago. bought a boat with a cracked 4.3 , went back in with a 5.0 beacuse that was the biggest engine offered with. in retrospect should have dropped in a 5.7. probably the 4 bbl upgrade isnt worth it unless you can find a used manifold and carb...
  3. Scott06

    Mercruiser 140 Points to Delco EST results in low RPM at WOT

    you are setting the base timing correctly, and total is correct, unless balancer has slipped so it is not indicating TDC correctly anymore. would also think fuel is ok based on your comments just thinking a sanity check as we may be running out of options . did the plunger for the power valve...
  4. Scott06

    Ford 302

    Yeah if you hadnt just put a new engine in i would suggest a 351…
  5. Scott06

    Ford 302

    15-25 more hp. You need an intake, carb, fuel line and throttle bracket mods. I think the 302 ford came in both versions from Merc so you can look up what HP would be with both. I doubt you will notice the fuel consumption difference. I think you will find the smaller diameter primaries on a...
  6. Scott06

    Mercruiser 140 Points to Delco EST results in low RPM at WOT

    Are you putting it in base mode when you set the 1 d BTDC? And you have verified the 24 degrees all in timing with a light or you mean it should supply 24 degrees total advance? Have you checked the strength of the spark with a spark gap tester? Try with tach disconnected. Wondering if tach...
  7. Scott06

    $2500 boat

    Just keep an eye on the oil. My neighbor used his boat 3-4 times after he was too lazy to winterize before he saw water in the oil.
  8. Scott06

    7K.-

    The newer VP gas engines that I believe are still GM based go up to 5800 and 6000 rpm. https://www.volvopenta.com/en-us/marine/products/aquamatic-sterndrive-gas/aquamatic-sterndrive-gasoline-engine-range/v6-tcc/#specifications...
  9. Scott06

    Ford 302...21 foot fiberglass with cuddy

    Personally i prefer 4 blades. My primary use is loaded down water sports. Typically you will see better holeshot, lower planing speed at the expense of a little top speed with a 4 vs a 3 blade.
  10. Scott06

    Alpha 1 Gen 2 drive shaft seal?

    The seal is in side the upper housing so you will not see it from the outside. I believe the vertical drive shaft normally moves up and down about 1/4” so looks ok to me
  11. Scott06

    Ford 302...21 foot fiberglass with cuddy

    So with 10 degrees initial plus the 24 centrifugal you should see 34 degrees total advance by 3500 rpm or so. You can check this on the muffs just briefly rev it. especially with an older mechanical advance distributor that can get hung up or corroded, you just want to verify you Are getting...
  12. Scott06

    Anyone run Hartland tires from discount tire?

    I purchased these Carlise tires in 2016 and have worked flawlessly, no signs of cracking or dry rot. Similar use limited towing, in winter they are inside in summer trailer is outside in the sun https://www.amazon.com/gp/product/B0055BPQLC/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
  13. Scott06

    what size kicker should I get.

    On a similar sized boat (but fiberglass so would have been heavier than AL) had a 9.5. This was for a fairly large lake ( 40 mi long) for lake trout trolling
  14. Scott06

    Carburetor paint

    yes
  15. Scott06

    Carburetor paint

    Eastwood offers this carb renew paint which mimics the original zinc dichromate coatings. same as in automotive resto world just paint it merc phantom black or i have had good luck with satin eastwood diamond clear for my driver quality work...
  16. Scott06

    3.0 volvo short or long block

    Yes the 1990 and up 3.0 will work for your application, you will also need the manifold and check the power steering cooler as that is probably busted too. Likely you will find the block cracked just below the head when you pop the manifold off.
  17. Scott06

    3.0 mercruiser ran for 5 min good. Then Just died?

    This - dump a little fuel down carb measure fuel pressure for a few seconds while it is running
  18. Scott06

    Cracked Block Replacement

    Back in they day ( ok a handful of years ago) they were $2K- more like $3600 now ... https://www.michiganmotorz.com/5-7l-vortec-marine-engine-1996-current
  19. Scott06

    Bought a new long block and wondering about the coupling and gimbal bearing.

    I agree with Lou definitely want to prop it so it can swing 5k. You have the same base engine used on MPI motors that I think the rev limiter is 5200, so no issue. In a heavy boat like that you are way better off being slightly under propped. Since you are swinging a 15" now you may actually...
  20. Scott06

    Cracked Block Replacement

    Not sure a project is best for a first boat , or have you been around boats in your family ? FWIW NADA on that boat is about $12-14k . Not sure if the classic Bayliners of this era had wood floor and stringers or not. If they do definitely first things first make sure the structure is in good...
Top