Search results

  1. R

    1969 6HP Impeller replacement

    No need to remove powerhead to change impeller.-----But there are some steps that need to be followed to get the powerhead seal pin to come through a slot.------The 69 model has needle bearings on big end of the rods.-----Thermostats are often missing or stuck open.
  2. R

    1979 OMC Gear Lube

    Well-----That mess is no surprise at all.----Looks like some repairs had been done already on it.-----Support the hull in a frame.----Cut that junk out and put some composite material in there.-----Most folks would say that there are better / easier projects around.-----Your location.
  3. R

    1979 OMC Gear Lube

    Well----60E ---appears to be from the Bracebridge / Muskoka area.------I see ( in the pictures ) some issues with stringers / wood under the floor in your future.
  4. R

    Trying to start a 1967 33hp Evinrude no Generator

    Or bring it over for a tutorial on how to look after this fine motor.----No manual needed here for that simple machine.
  5. R

    1979 OMC Gear Lube

    You might not be aware that these OMC sterndrives are not high on the hit parade.------Be prepared to do the maintenance or replace drive / replace boat.
  6. R

    1979 OMC Gear Lube

    Use mercruiser gear oil.----Or OMC / BRP oil called ---HI-VIS----In that drive.
  7. R

    Trying to start a 1967 33hp Evinrude no Generator

    Facts for you.-----This motor does not need 12 volts to run !-----It does not need a generator to run.------Pull the flywheel ( 3 bolts 1/4-20 ) to inspect points and coils.-----If coils are original they will likely be cracked and you need new ones.-----These are an elegantly simple , reliable...
  8. R

    Worth Fixing?

    You either fix these things or buy a newer boat.-----You get a part time job to make the money and use " after tax coins " to buy the better boat.----Or roll up your sleeves and fix this one.----You gain satisfaction and save $10 every hour you spend on it.-----All depends on your ambition and...
  9. R

    Force 125 lacking power

    With the lack of power there is a issue with 1 of 5 things.-----Wrong timing or no spark on one cylinder.-----Not enough fuel / too much fuel going in to one or more cylinders.---Lack of compression in one or more cylinders.-----Lack of crankcase compression in one or more...
  10. R

    Gear oil leak 1985 9.9 Evinrude

    Just run it.-----But remember these motors do NOT have an overheat warning / shutdown system.------They will overheat and run till they come to a " dynamic halt " and it results is expensive repairs.----Your call I say.
  11. R

    Gear oil leak 1985 9.9 Evinrude

    Many different answers / opinions will be given.-----I do not know the maintenance history of your motor.------I do not know the tools and ability that lives in your workshop.--------This could well be normal , from oil mixed with the fuel.----No water in the gear oil is a good sign.----I own...
  12. R

    1978 18ft Mariner: I won this "Pig in a Poke" on Ebay..!

    Looks like a homemade center console.-----A package like that would be $30,000 + new.-------A very good plan to remove floor / replace transom.------A boat like that properly fixed will give you years of enjoyment.
  13. R

    Default Knocking / rattle sound in 40hp outboard - Lower leg?

    Shift linkage is not the issue.-----Check spark on each lead.-----Possibly running on 2 cylinders.
  14. R

    Deck repair looks like might need new stringers and any other advice.

    Typical boat construction.--------Make a hull in a mold.---Then add some plywood structure.-----Pour in some expanding foam.----Put floor down.-----Foam adds strength and quieteness. -----Done.-------No concern as to what happens when water gets in there after 15 years.-----Doing a boat...
  15. R

    1984 johnson 90hp carb leaking fuel out air cleaner

    Is there a wee hose that comes from the back of the air box?-----If yes , does that hose go to a nipple ?
  16. R

    1982 15HP Johnson

    Should be exactly the same.----What do you mean by " government work " here ?
  17. R

    Tilt and trim unit interchange.

    The concept of the SPL model was economy / lower price.-----Therefor no trim / tilt or oil injection from factory.
  18. R

    75hp Lower Unit - confirming reverse gear is engaged

    Sorry-----You have to look on another parts page to find the " shift slide "----for this motor !!
  19. R

    75hp Lower Unit - confirming reverse gear is engaged

    The control box and cable hold it in reverse.
  20. R

    75hp Lower Unit - confirming reverse gear is engaged

    ??----There is a strong spring in there.-----It will kick it out of reverse in the blink of an eye.-----Hold the shift rod in reverse and test.----This is simpler than you can imagine !
Top