Search results

  1. flyingscott

    Primer leaking Merc 25hpXD

    No, I dont know why you would have adjusted the float. You may have a bad fuel pump diaphragm also. Which is why it is important to service those correctly with a quality kit.
  2. flyingscott

    Fuel connector compatibility issues.

    Mercury has 2 different connectors that look very similar. You need to find out which one you're uses. The serial # of the motor will tell you which one you need.
  3. flyingscott

    8hp Mercury revs up, then stalls! See video

    Have you adjusted the low speed needle? Sounds like a lean sneeze
  4. flyingscott

    1985 Mercury 18xd conversion to 25hp?

    You need the linkages for the remote throttle and shifter. You cannot use the tiller system for that. You also need to change the front bracket out. Where are you located?
  5. flyingscott

    Primer leaking Merc 25hpXD

    You need to replace the primer diaphragm. You should ave ordered a carb kit with the fuel pump and primer diaphragm. Did you make sure the check ball is not jammed in the spring under the primer?
  6. flyingscott

    1985 Mercury 18xd conversion to 25hp?

    You also need the exhaust tuner.
  7. flyingscott

    1990 70hp Evinrude Synchronization procedure problems

  8. flyingscott

    1990 70hp Evinrude Synchronization procedure problems

    You do not care about idle timing. On muffs set the idle for 1100 rpm and if you have adjustable carbs set them at 1.5 turns out for a start.
  9. flyingscott

    Do I need a new block or small side case half?

    What did you use to seal it? You need to seal it with something like loc-tite 518.
  10. flyingscott

    Considering rebuilding 1990 Johnson 70hp - questions

    What is bad compression? I believe 1990 was the first yr for decompression holes.
  11. flyingscott

    SCOTT ATWATER IGNITION COILS

    Ok I looked at mine and the 74-76 OMC coils should work. Are you sure you do not have bad set of points or condenser?
  12. flyingscott

    McCULLOCH not running right

    What year is your motor? There was no 45 up in 1957. Does it have dual carbs? Does spark jump a 1/4" air gap? What is your compression? Have you cleaned the carb? Is the fuel pump Diaphragm in good condition? Fuel pump check valves good? And if it actually says McCulloch on the hood it is 64 or...
  13. flyingscott

    SCOTT ATWATER IGNITION COILS

    Let me look at mine but I believe OMC coils work you just need to mount them. The 74-76 OMC 9.9/15 coils would probably be the best.
  14. flyingscott

    water in VRO tank

    Replace the cap on the oil tank and clean and re prime.
  15. flyingscott

    SCOTT ATWATER IGNITION COILS

    Join the AOMCI they will be a great source of info and parts. Where are you located?
  16. flyingscott

    96 johnson 9.9-15 carb. Choke ??

    Find a manual primer from a manual start 25 hp and plum it in.
  17. flyingscott

    9.9 kicker motor with sterndrive questions

    Is your kicker a 2 or 4 strk?
  18. flyingscott

    pull start electric start conversion

    The kit is expensive. Your best bet is to find a parts motor I have had good luck finding pontoon motors that people wreck. Most of those have electric start. You will need a ring gear for the flywheel and the starter motor, a solenoid and starter switch. The starter switch is mostly NOS now but...
  19. flyingscott

    1986 25 hp Johnson remote start. Small hoses location

    Sorry spell check sucks. If you are talking about the primer ,one small nipple goes to the intake and one goes to the carb. Now if you have the third nipple behind the fuel pump. Then you need to tee off one of the smaller lines does not matter which one.
  20. flyingscott

    1986 25 hp Johnson remote start. Small hoses location

    Fuel in goes to the round piece on the pump. Out goes to the bottom of the carb and that line must be free off to the primer. Or are you resting the primer? Thing with the red lever?
Top