Search results

  1. C

    Evinrude 9.9 HP Model # 10924B

    btw you have electric start ... why not hook up a battery and get it going. very basic circuitry find the solenoid and follow the small control wire to the start switch ! basic for 1984 should be similar to yours even if earlier model. yellow red to solenoid should activate the...
  2. C

    Evinrude 9.9 HP Model # 10924B

    I restarted and keep pumping the bulb than it keeps running. hand pump it again and make certain the tank is ABOVE the engine try to start it... if it runs the pump is faulty install a new one . (up to you $$ ) The only reason the pump would not work is that the crankcase pressure pulse on...
  3. C

    Evinrude 9.9 HP Model # 10924B

    Did not work meaning what..... blow test failed ?? Why don't you try a new pump. That kicker looks real clean and giving up on it would be a shame. Reassembly (orientation of parts) is confusing the first time around.
  4. C

    1990 Evinrude 9.9/15 still starting rough

    so what are you saying... problem fixed ?
  5. C

    1990 Evinrude 9.9/15 still starting rough

    Leroy's has lots of info on the 9.8-15 you should read starting with this one....see HARD STARTING https://www.leeroysramblings.com/Johnson%209.9_15.htm see all his topics https://www.leeroysramblings.com/Outboard%20Motor%20Related/OMC%20outboard%20related%20articles.html
  6. C

    1990 Evinrude 9.9/15 still starting rough

    try openning up the LS needle 1/4 CCW . Starting an engine is done by pulling fuel from the LS circuit of the carb and make certain that little tube is set properly
  7. C

    Evinrude 9.9 HP Model # 10924B

    your engine is telling you it wants fuel ... hand pumping is not the solution.... it is an indication your pump is not sucking gas from the tank and not pushing it to the carb !! If the carb was full of fuel the engine should run longer but does not an indication the pump is not filling it...
  8. C

    1990 Johnson 15hp only start with carb disengaged

    no tiller gears... :-( great that solves one problem. :-)
  9. C

    Evinrude 9.9 HP Model # 10924B

    looks alone wont cut it when you reassemble...... the check valves must be oriented correctly as well as the metal layers which I mark (scribe) with sharpie to orient then as they were when I started. final test is a blow test did you look at he rebuild link I posted above ?? I...
  10. C

    Evinrude 9.9 HP Model # 10924B

    lift the tank above the carb after filling it... gas will siphon down to the carb and the engine should run. but....your fuel pump is also acting like a check valve after passing fuel to the carb. You may be so unlucky to have a bad pump and... a bad check valve in the hand pump !! do a...
  11. C

    1968 3hp Johnson

    See post #7 your fingernail must not snag going up or down at the coil juncture with the mag plate . if needed use a screwdriver to pry the coil face backwards to line it up....or has suggested slightly enlarge the bolt hole (S) enough to recess the coil from the edge. use star washers to...
  12. C

    Evinrude 9.9 HP Model # 10924B

    those pumps are tricky did you do a blow test after reassembly air IN to OUT barb should pass No air passes from OUT to IN barb . if hand pumping helps the pump needs fixing
  13. C

    Golden Jubilee Evi Sportwin 10 - Should I convert?

    they stay put with lock tite ... blue is semi permanet red is permannet so use blue ¸if the insert rim interfeers with the plug the cyl head needs to be reamed a bit to sink it below the edge see utubes...
  14. C

    Evinrude 9.9 HP Model # 10924B

    I am certain the Zodiac folks can tell you what to do to glue a patch and what glue to use. try some googling https://www.amazon.ca/zodiac-patch-kit/s?k=zodiac+patch+kit
  15. C

    1973 4hp Evinrude

    you don't need a fancy timing light to service a 4hp. Just set points at .020 with the cam lobe's high point or use the voltmeter test. Yet .020 isn't all the t important was is .. is that point open at EXACTLY TDC the VOM will tell you or a simple LED or bulb on a battery will tell you...
  16. C

    Evinrude 9.9 HP Model # 10924B

    if you ever decide to open and service those square pumps keep an eye for small springs and tiny mushroom caps. To re-assemble I put on small drop of crazy glue on the spring's locating dimple and on the mushroom caps to secure then on the spring ends so they don't fly off to never to...
  17. C

    Evinrude 9.9 HP Model # 10924B

    these small pumps are everywhere on amazon and folks like or don't like them. I have used them with no problems but if you do want oem any dealer will surely have these pumps or order it . rebuilding the pump is easy after you have done a few first one is always tricky read read read ...
  18. C

    1990 Johnson 15hp only start with carb disengaged

    the roller is set centered to the cam but at the tiller arm it's maxed full slow so I can only go full throttle from there. ???? if the cam follower is centered on the mark the tiller should be at or close to START....works like that on all obs ... if you rotate the tiller to FAST the mag...
  19. C

    1992 Johnson TJ25ELENS 25 hp

    check venting ...try hand pumping fuel in case fuel flow is impaired check fuel pick-up. does PH get HOT !!! check water flow is water to hot !! recheck for sparks when it does not restart after idle shut down. did you clean out the drip chamber under the welch plug when you did...
  20. C

    Golden Jubilee Evi Sportwin 10 - Should I convert?

    dying comes bad fuel flow no sparks or bad condensers shorting out under heat.
Top