Search results

  1. C

    Evinrude 25202r no spark

    the hv connection is the point of connection of the plug wire into the coil. today's coils have a screw pin where the 7mm plug wire is actually screwed on the pin. old coils had simple needle like pins. it is very important no to use automotive CARBON fiber wires..... use only solid...
  2. C

    Evinrude 25202r no spark

    IMHO... this is a standard magneto and both coils should show a reading from plug boot to coil secondary to ground.... somewhere from 3-8 kohms depending on manufacturer. could bad coil, bad HV connection (corroded) bad pin prick in the boot open plug wire due to flexing etc...
  3. C

    Evinrude 25202r no spark

    it measures the coil resitance, plug wire and plug booth pin contact for proper continity.
  4. C

    Evinrude 25202r no spark

    when Telco's ran central offices on gazillion relays.... lapping (burnishing) relay contacts was the usual remedy.
  5. C

    Evinrude 25202r no spark

    post the resistance values as measured from plug boots to engine frame . look for a steady ohms value 3-8 kohms approx while moving the throttle from idle to high speed .
  6. C

    1996 evinrude 70hp electrical issue

    hopefully it won't lown again otherwise you will need to find the cause .
  7. C

    9.5 issues

    are you confirming it idles ok with the hood off ?
  8. C

    9.5 issues

    links and carb adjusted ? is this a new problem or ... .a new motor to you ?? did it ever run good does it run ok at higher speeds above the ildle tried adjusting the side knob to up the idle rpms ??? have you adjusted the timing ??? what ohms value do you see between boots and...
  9. C

    1977 Johnson 75 Stinger dies when put in gear

    the orifice plug is just a hole" if you cleaned them they should be OK ... be focus on other stuff for now .
  10. C

    ELECTRICAL CONNECTOR TOOLS

    Most of those amp connector pins have small locking tabs. the idea is to insert a tool to overlap the locking pins ...sometimes one pin sometimes 2 pins! I have managed to extract some by flattening different size finishing nail by hammering them out on an anvil and grinding the...
  11. C

    1995 Johnson 130 No Power Under Load

    The carbs have been checked and cleaned.... ....it gets up around 2k rpm and fell flat on its face unless someone was priming the ball on the fuel line don't mean to be picky but exactly was done on the carbs. were all orifices cleaned and air blasted. the HS orifice plugs...
  12. C

    Battery sparking

    no offfense but.... I had a 9.5 hp as my side kicker for trolling... trolling which does not have to be at the other end of the lake all the time . I ran a 3 gal tank on the 9.5 ahd found that even trolling during several days was adding up at today'S 7-8$ Cdn per gallon (gas here today...
  13. C

    1995 Johnson 130 No Power Under Load

    2 years sitting....have you serviced the carbs ??? as a bare minimum have you cleaned out the High speed orifices the bottom of the carbs ...just behind the lower carb bolt have you checked all filters incl. tank pick up ??
  14. C

    What type of hydraulic fluid to use in '98 50hp Johnson? Replace relays too while I'm at it?

    btw my 75hp ETEC was doing the same.... in my case a T&T reseal was in order. been ok since :)
  15. C

    What type of hydraulic fluid to use in '98 50hp Johnson? Replace relays too while I'm at it?

    cylce the system a few times to purge any air...keep topping the oil after every cycle till 100% full
  16. C

    Looking for Service manual for 1982 evinrude 2hp (E2RCNE) outboard

    what compression #s do you get ... if OK don'T mess with it just do the top side stuff ! http://www.leeroysramblings.com/OB%20carburetor_repairs.html http://www.leeroysramblings.com/Troubleshooting%20OB.htm http://www.leeroysramblings.com/johnson_magneto.htm
  17. C

    Looking for Service manual for 1982 evinrude 2hp (E2RCNE) outboard

    not much to service on a 2hp what issues do you need the book for ??
  18. C

    Strange leak on 9.9 Johnson

    16mb file... !! I am not openning it.
Top