Search results

  1. C

    4 HP Evinrude Coils

    these coils are common to OMC magnetos for about 20-25 years and have changed numbers across the years so don't worry to much about finding the same numbered coils it is critical that to avoid any wrong answers from folks helping out on your project that you list the engine model on...
  2. C

    Head gasket orientation 1990 4hp E4RESR

    see video... (683) Can JB Weld fix a cracked cylinder head? See the proof!! - YouTube I think you could fix that small indentation with JB on a water cooled cyl head
  3. C

    Head gasket orientation 1990 4hp E4RESR

    How to use AlumiWeld, do it yourself aluminum propane welding repair kit 2 important point clean the part to remove all form of oxydation (SS brush will do) heat the part NOT the rod heat the part till the rod melts grind the excess aluminum back to what you want I used the product...
  4. C

    79 35hp evinrude wet plugs

    typical layout...the fuse feeds the B post on the key which shares it with the selenoid to start but.... reverts to feeding the ACCESSORIES "A" terminal on the key while "ON" any problem on the accessories distribution . or faulty switch will blow the fuse ex: bad tach, bad...
  5. C

    50473m 50hp evinrude lark ignition wiring diagram

    continuousWave: Whaler: Reference: Ignition Switch maybe you can find something in here to help
  6. C

    Head gasket orientation 1990 4hp E4RESR

    just saw a you tube with a fix similar to your problem using EXTREME HEAT steel epoxy Amazon.ca:Customer reviews: J-B Weld 37901 ExtremeHeat High Temperature Resistant Metallic Paste - 3 oz good up to 500 deg. may work for you ?
  7. C

    50473m 50hp evinrude lark ignition wiring diagram

    can't vouch it is 100% if you had more wires it would be a problem :-) trace back the wires to find out where they go and do
  8. C

    Newly bought Johnson 7.5

    impeller is the rubber star in the pump housing visit utubes for lots demos
  9. C

    1980 70hp Evinrude clatters and hard to get into Forward gear

    is this a new problem recently ..sounds like some linkage is not adjusted properly or gears destroyed partially by improper shifting procedure by previous owner any metal chips on the oil plug magnet ??
  10. C

    Head gasket orientation 1990 4hp E4RESR

    tab up and holes lined up top left and right are not symetrical like the middle and bottom bolt holes so you must line up the top bolt holes with the gasket
  11. C

    50473m 50hp evinrude lark ignition wiring diagram

    is this any good ... Evinrude Ignition Switch Wiring Diagram - Bing images
  12. C

    Exhaust coming out under the power head

    rats mice bees who knows what lurks up that exhaust cavity :-) a dead snake maybe ...
  13. C

    4 HP Evinrude Coils

    well... the 1982 4hp uses good old 0584477 available everywhere including china but.... coils (2) just don't "stop working" tell us more before spending good money . cracked ?? what ohms do you measure from the secondary High voltage pin and primary wires (usually 4-7 Kohms)...
  14. C

    Evinrude 1975 85 hp electrical starting issue

    still raining ...?
  15. C

    Losing a cylinder intermittently ‘86 50hp

    have you done anything electricaly ( clean plug wire ends , measure coil resistances to compare etc..) what about the carbs..... any work done on the LS circuit jets and drip chambers some don't like it but try simple stuff like a good shot of seafoam it did wonders on my snowblower...
  16. C

    Newly bought Johnson 7.5

    don't forget to change the impeller (age unknown to you) and replace the gearcase oil (see if any water got in if so a GC reseal may be in order. use new nylon washers as it may be just the washers not doing their job to seal the GC) unscrrew the top Idle adjustment . needle a half turn...
  17. C

    1956 Johnson 10 HP QD-17

    it is suppose to be solid (no holes) ) but that fix ain't so bad... you do not need to worry about the filter being clogged up. just clean the brass screen and reinstall it :) in retrospect it is a good solution and a lot cheaper than chasing a new filter . It is a solution I will use...
  18. C

    2010 Evinrude etc 60HP won’t stay running

    feeding it fuel ??? how ..with the fuel primer pump ? did you check the lift pump & screen for clogging....tank fuel pick-up ok ? tank venting ok ?
  19. C

    1956 Johnson 10 HP QD-17

    try soaking it in hot water instead.... don't force it or break it !!
  20. C

    Evinrude 1975 85 hp electrical starting issue

    Assuming the diagram reflects your engine .... the selenoid gets a ground via the safety switch and the momentary 12V to energize it, comes from the "start" key via the neutral switch . Critical points are the 12v supply feeding the key assembly switch operation to apply 12V to...
Top