Search results

  1. alldodge

    2009 Mercruiser 3.0L TKS stalling

    Check your fuel delivery system. Fuel filter contents in clear container. Disconnect power to coil and remove fuel line. Crank motor and see how fuel comes out, a little or a lot.
  2. alldodge

    exhaust flapper question

    Agree VP stopped using flappers
  3. alldodge

    Engine wont shut off with key

    That's what I'm saying, the power is coming from the solenoid. The slight spark is normal because it powers the motor back up, same as turning key ON Figure you have a multi meter. Check for a connection between I and the right side post on the old solenoid. If there is a connection and the...
  4. alldodge

    Engine wont shut off with key

    I've got nothing then, just know how it should work You removed the Tan wire (yours is Green) and have 12V on the post, not the wire. That wire feeds power direct to the coil and back to the key Maybe the new solenoid is bad, or its wired internally different
  5. alldodge

    Hard starting after drifting with warm engine, Volvo Penta 4.3, V6-200-J (2017), A699123, VPGAS063873, EFI fresh water cooled, SX outdrive

    Sounds normal for 2 electric fuel pumps pumping, but my ear/speakers are not the greatest anymore
  6. alldodge

    Hard starting after drifting with warm engine, Volvo Penta 4.3, V6-200-J (2017), A699123, VPGAS063873, EFI fresh water cooled, SX outdrive

    Link doesn't work
  7. alldodge

    Engine wont shut off with key

    The Ah Ha moment. New solenoid but terminals are different. Swap the Bat and Starter cables The Ignition and Starter are and "should be" connected together. This way when the solenoid energizes the starter it also supplies full volts to the coil for starting. When key is released power is...
  8. alldodge

    Engine wont shut off with key

    With full volts it has to be the solenoid has gone bad like Kenny mentioned T prove, remove the Tan and see if its still on wire or just the post
  9. alldodge

    Electrical Issues after replacing trim switch/sensor 7.4 EFI/MPI

    You sure, most have a lead from the starter post to the trim
  10. alldodge

    Engine wont shut off with key

    So its back feeding as Kenny mentioned, or might be from the key I have 2 different wiring diagrams and one shows the yellow on the side with the Bat Positive lead, and another which shows the Tan You have Yel on start and Grn on Ignition Remove the Yel on the key switch and see if wire remains...
  11. alldodge

    I Bonds

    Admiral and I did the online sign up June 14 to purchase I Bonds (current 9.62%). At the time both came bak with unable to verify, please fill out this form and get a Bank Medallion stamp signature. Ok everyone want's to get it so this may help ferret out the Bots. Estimated wait 10 to 15...
  12. alldodge

    Engine wont shut off with key

    Did ya happen to swap the Starter and Battery leads on the solenoid, or even the smaller Tan wire ?
  13. alldodge

    Hack Job Sending Unit

    Another idea, get everything good and clean the JB weld it on. Again it will be a real pain if it ever did leak or had another problem
  14. alldodge

    Hack Job Sending Unit

    Center punch then might take the most turns but far less chance for heat to build up with a brace bit drill Use a shop vac outside the boat and just the hose blowing not sucking, by the bit to help from keeping fumes from building. I do like Chris idea of using rivets. Only issue is if...
  15. alldodge

    Electrical Issues after replacing trim switch/sensor 7.4 EFI/MPI

    Its wired correctly but there must not have been a fuse inside the fuse holder
  16. alldodge

    Hack Job Sending Unit

    Manual drill not electric Drilling non-ferrous material
  17. alldodge

    Engine wont shut off with key

    If you have a TKS carb check the diode What motor?
  18. alldodge

    Pro Torque starter bolts from Mercruiser

    Been many discussions here lately of starter bolts. I measured the PMG starter and its 3 3/16 wide. ARP and Dorman sell 3 5/8 long starter bolts Do you know how long the ones you got where? Looking up 10-805343 it shows 6 inch long and NLA at BAM https://www.mercruiserparts.com/8053431-screw
  19. alldodge

    Replacing Flotation Foam

    The foam adheres to the deck https://forums.iboats.com/threads/chrylser-105-conqurer.657617/page-3
  20. alldodge

    Electrical Issues after replacing trim switch/sensor 7.4 EFI/MPI

    It looks like both the ALT feed and motor feed are melted? If that's the case then it shouldn't happen unless the battery cable was installed to bypass the fuse
Top