Search results

  1. alldodge

    Alpha One-g1. Shift problem when Tilted

    If I'm understanding you correctly This is the lower and the shift foot is facing directly FOR and AFT , good This is the upper and its not facing direct FOR and AFT The cable needs to be adjusted some more
  2. alldodge

    Merc Quicksilver Gen 2 Kill Switch

    Measure the continuity of the switch action. The 4000 comes in a few styles and has 2 different switches. One for outboard (2 cycle closes when activated) and one for I/O (opens when activated)
  3. alldodge

    5.0gi to 5.7 swap

    Don't listen to the shop, and as Bondo mentioned don't change the cam. You will need the ECM reflashed which isn't hard, just need the right software like MEFI Burn. With this software and the right Bin file its a easy swap Could contact Bob at OBD Diagnostics or a member on Offshore only...
  4. alldodge

    2002 Volvo penta Gxi 5.0 beeping issue

    I'm unable to verify Ac 213-96 is for your motor. It comes up 1996 and older, so pre vortec This one comes up as vortec and also Merc and VP. Not saying yours is not correct, or that this will fix the issue, just not able to verify the part...
  5. alldodge

    Won’t stay running

    Put your meter on each side of the diode and measure resistance, being open it should read infinite resistance. A good diode will read low with leads on in one direction and by swapping leads it will read high
  6. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Disconnect solar, turn something ON for each Bat for even 1 minute and see if it stays up
  7. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    I like to see 14.5V with motor running and 12.7V after sitting for an hour or so
  8. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Wish I had something but there isn't much for CAT motors yet Might have something to do with your solar hook up
  9. alldodge

    Stalled while idling now it cranks but no star or sparks

    Crossing fingers In that case you might have break before make switches, and they should never be switched when a motor is running
  10. alldodge

    Not getting a spark boat will not start

    Looks like carb motor Your kill switch flipped OFF maybe?
  11. alldodge

    Stalled while idling now it cranks but no star or sparks

    The key powers up the ECM and MPR. If they don't get power, nothing works Fuses and relays.
  12. alldodge

    Won’t stay running

    Yes you can check it with just resistance. If you get zero ohms then its open and from your problem that is what the issue is Yes, if the diode opens its like cutting the wire.
  13. alldodge

    Stalled while idling now it cranks but no star or sparks

    ok, if you have Bat switches that make connection before breaking connection there is no issue. If they break before Make then a ALT may have fired. If ALT spiked it could have taken out the ECM. Hope the worst might have blown a fuse Need to find out if the cables are still connected to the...
  14. alldodge

    Won’t stay running

    What your saying is your not understanding what was said and shown in the drawings. In short , if the diode coming from the ALT has opened up internally, you have the same problem
  15. alldodge

    Stalled while idling now it cranks but no star or sparks

    Did you move cables around while the motor was running?
  16. alldodge

    Won’t stay running

    While the guy talks about if the other diode (not the one your issue might be) is causing engine to not shut off. This is "NOT" the way to fix that problem. There is a shorted diode and what does he do, he adds another diode to fix the current problem. Issue with that is what happens when the...
  17. alldodge

    Won’t stay running

    Diode is not in the ALT its inside the harness
  18. alldodge

    Mercruiser 383 no spark/no fuel

    Serial number comes up as a 3.0 TKS at Merc site Yes look thru the hole
  19. alldodge

    Does anyone have pic of distributor on Merc 7.4 Gen V?

    PO may have had the head machined and didn't check for length of push rod or might have put the wrong push rod in
  20. alldodge

    Won’t stay running

    Agree check the diode
Top